Question about Renault Sportwagon

1 Answer

I need to remove the panel as the window drops into door for no reason and i have no control from switch to get it back up

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,510 Answers

To remove the door panel, remove any screws that are in the vicinity of pull handles and door pockets. These screws will be under little trim covers that you need to prise off to get to their heads. Look for the screws around the edge of the panel and also the screw in the latch release handle recess.
The lock knob, if there is one there, will have to be screwed off and then carefully work your way around the door, freeing the panel's clips from their holes in the door frame. (Doot panels are brittle and clip break out easily).
Finally the panel will probably have to be lifted out if the window slot. (If the panel does not come off, work out what is retaining it and remove that screw or slide it off the clip that is still holding the panel. Disconnect any electrical plugs behind the panel. Under the panel you will find a plastic dust sheet that is stuck to the door frame, remove this carefully, you will have to replace it before replacing the panel.
You need to work out why the window has dropped. It could be a loose slide extension or a broken operating arm or joint and these need to be repaired before any further work is done.

Posted on Mar 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

Were does the LH mirror on a 2011 f-250 connect. Removed mirror but disconnect is located some were in door or body. need to know what needs to be removed to gain access


  1. Remove the front door trim panel.
  1. Position aside the front door watershield to gain access to the exterior rear view mirror control switch electrical connector.
4.Disconnect the exterior rear view mirror control switch electrical connector
ganyapr_7.jpg
as you see you have to remove the door panel to have access to the electrical connector in case that you dont know how to do it here are the instructions

NOTE: Left front door trim panel shown, right front door trim panel similar.
  1. Remove the sail panel.
    • If equipped, disconnect the electrical connector

  2. If equipped, lift up and remove the exterior rear view mirror control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, lift up and remove the window control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, remove the window regulator handle.
    1. Position the window regulator handle cover aside.
    1. Remove the window regulator handle screw and regulator handle
5.Remove the door trim panel center screw cover
6.Remove the 2 door trim panel center screws
7.Remove the 2 door trim panel lower screws
  1. NOTICE: Do not pull directly outward on front door trim panel as damage will occur.
    Remove the front door trim panel.
    • Lift upward to remove the front door trim panel.
  1. NOTICE: Insert the lower panel tabs first or they can break when installing the front door trim panel.
    To install, reverse the removal procedure

Feb 20, 2011 | 2011 Ford F-250 Super Duty

1 Answer

Driver's side power window was inop. Window failed to go back up. Chevy dealer replaced the regulator motor and now working. Now the power dood lock switch on drivers side won't unlock doors.. Is the...


Hi, that wire is disconnected when the door panel is removed to work on the window motor. Take the car back and ask them to reconnect your door locks. If you want to fix it yourself, you may be able to access the connector by removing only the control panel where the door lock switch is installed. Remove any visible screws and then pry gently to pull up the panel. Odds are, however, that the whole door panel will need to be pulled loose to find the cable. You can possibly just pull the bottom of the panel loose, but do it carefully. Feed the wire back up to the control panel and reconnect to the switch. Thanks for using Fixya.

Jan 24, 2011 | 2003 Chevrolet Venture Passanger

2 Answers

When you open the door, the window drops a little and doesn't come back up until door closes normally, but my problem is when i open the door the window drops a little like its supposed to but instead of...


You may need to store the end position of the windows in the control unit. I would try the following, with the door closed, and the window partway open: Close the windows with the rocker switch ONCE. Then press the front half of the rocker switch again, this will store the end position in the control unit. Good luck!

Oct 18, 2010 | 2001 Porsche Boxster

1 Answer

I want to remove passenger side rear door panel because window is down and won't stay up


Hi,
Hi!!

Here is a little information on how window regulator works. Also step by step instruccions on how to remove and install the window glass.

Door Glass & Regulator Power Windows
Diagnosis & Testing
When the rear window lockout feature is enabled, the circuit is open and no voltage is supplied to the rear window switches. When the feature is not enabled, the circuit is connected to battery positive voltage. If this circuit is shorted to ground when the lockout feature is not enabled, the PWR WDO circuit breaker may cycle continuously OFF/ON until, either the lockout switch is pressed to open the circuit, or the circuit breaker is permanently damaged. All windows may be partially or totally inoperative while the fault is present.
Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.
Removal & Installation
Window Motor & Regulator
  1. Position window approximately half way down in the door.
  2. Remove the interior trim panel.
  3. Remove the water deflector.
  4. Tape the window to door frame to prevent it from moving.
  5. Remove the three front door window regulator motor screws.
  6. Disconnect the electrical connector from the window regulator motor.
  7. Remove front side door window regulator motor.
  8. To install, reverse removal procedure.

Window Switch
Front
  1. Remove the front door pull cup screws and pull cup from the front door trim panel.
  2. Disconnect the electrical connectors from the front door power window control switch.
  3. Remove the front door window control switch using a small, flat-bladed tool at the side of the switch.
  4. To install, reverse removal procedure.

Rear
  1. Remove the rear door pull cup from the rear door trim panel.
  2. Disconnect the electrical connectors from the power window control switch.
  3. Remove the rear door window control switch from the pull cup using a small, flat-bladed tool at the side of the power window control switch to release the power window control switch retainer.
  4. Remove the power window control switch from the rear door pull cup.
  5. To install, reverse removal procedure.

Sep 07, 2010 | 2002 Buick Century

1 Answer

How to remove drivers door panel on 1999 ford escort. I need to repair the windows switch for the drivers side. My window is in the down position and won't come up when I push the button. All other windows...


Remove the front door pull cup screw 1152a96.gif

Remove the screw cap and the screw from the inside door handle and slide the handle rearward to disengage the hook from the inner sheet metal.
  • Disconnect the inside door handle from the front door latch remote control link
37470b2.gif

Remove the two-piece pushpins from the front door trim panel (23942).
2a1605a.gif

NOTE: Use a commonly available spring loaded trim pad removing tool with a long thin nose to prevent damage to the door trim panel.
Release the seven front door trim panel bullet nose fasteners and push inboard, then upward to release the front door trim panel.
  • If equipped, disconnect the master window regulator control switch electrical connector
cc0d2af.gif

Remove the retainer from the master window regulator control switch panel.
  1. Pull outward on the cup retainer tabs and remove.
  1. Remove the master window regulator control switch electrical connector from the retainer
ab8ff6c.gif

Jun 05, 2010 | 1999 Ford Escort

1 Answer

Need to remove drivers door panel


please rate if this helps. Section 01-05: Trim, Interior 1995 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION The interior trim component Removal and Installation procedures generally apply to all models. If some of the steps do not apply to the particular models being serviced, proceed to the next step. Trim Panels, Door Removal and Installation
  1. ssd~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not pry front door trim panel (23942). Prying on front door trim panel will break the hook retainers.
    Disconnect battery ground cable (14301) .
  1. Carefully pull front door trim panel finish panel (23712) away from front door trim panel .



    9e3f506.gif
Item Part Number Description 1 23713 Front Door Trim Panel Finish Panel 2 17B676 Outside Rear View Mirror Control 3 14028 Door Lock Switch 4 55928-S55 Screw (5 Req'd) 5 14529 Window Regulator Control Switch 6 23942 Front Door Trim Panel
  1. Disconnect wires from front door lock switches (14017), outside rear view mirror controls (17B676) and window regulator control switches (14529) , if equipped; remove front door trim panel finish panel.
  1. Remove front door trim panel retaining screw through front door trim panel finish panel opening.

    Trim Panels, Door


    83b257f.gif


    Item Part Number Description 1 20124 Front Door 2 23942 Front Door Trim Panel 3 383356-S100 Nut (2 Req'd Each Side) 4 56903-S58 Screw (2 Req'd Each Side)
  1. Remove interior lamp lens cover.
  1. Remove screw through interior lamp opening.
  1. Slide front door trim panel upward to disengage hooks.
  1. Rotate top of front door trim panel away from front door (20125) , and lift bottom hooks from front door.
  1. Disconnect window regulator jumper wire (14A630) .
  1. Remove front door trim panel.
  1. To install, reverse Removal procedure.

May 07, 2009 | 1994 Mercury Cougar

1 Answer

Front right door window will not go up or down, it is electric. it works, some times, and some times not. it is in the down position. Would like to move to up position. I live in Arizona, I need it up for...


does it act the same whether you use the driver door switch or the passenger door switch? Please rate as fixya if this helps. thanks

here's repair procedure

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
Trim Panel, Front Door, Explorer Hi-Series, Two-Door and Four-Door Removal and Installation
  1. Remove the two screws retaining the front door trim panel (23942) located above the window regulator handle (23342) . Also remove one screw in the upper front portion of front door trim panel .
  1. Remove inside door handle cup (22634) at the window regulator handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator control switch (14529) and outside rear view mirror control (17B676) , use notch located at lower end of outside rear view mirror control using a screwdriver to lift and remove.
  1. Remove outside rear view mirror control from front door trim panel pulling wire harness from inside of front door trim panel .
  1. From bottom of outside rear view mirror control, remove two screws and disconnect connector from switches. NOTE: Do not pull on the front door trim panel to remove clips from the inner panel holes.
  1. At each plastic clip location, pry the front door trim panel away from the door inner panel using the front door trim panel removing tool from Rotunda Moulding Trim Kit 107-00401 or equivalent. NOTE: Pay special attention to the cut-out in the door trim panel for the door handle, so that it clears the handle during removal without breakage.
  1. When wiring and disengagement of trim clips is completed, it is recommended that to remove panel, lift slightly to remove flange at the top of door trim panel from trough in the glass weatherstrip.
  1. Disconnect socket and bulb from illuminated interior lamp (13776) before total removal of front door trim panel. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the front door trim panel to the front door trim panel , firmly loading clips into slots provided on front door trim panel .

    Trim Panel, Front Door, Explorer Hi-Series Four-Door

    a9ce4e4.gif
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    9b5ccd1.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 20, 2009 | 1994 Ford Explorer Limited

1 Answer

Removing door panel


There's actually some more screws you missed.. they'll be hidden near the door handle and the armrest that you'll need to take off...once the panel's off, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Nov 16, 2008 | 2006 Kia Spectra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

xxxxxx xxx

Level 3 Expert

4844 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...