Question about 1990 Daihatsu Charade

1 Answer

How do you adjust clutch - 1990 Daihatsu Charade

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

Move circlip on corrogated cable ferrule where it attaches to the clutch lever in the engine bay.

Posted on Sep 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

2 Answers

Clutch plate location


Hi Timothy, The clutch plate is fitted between the gearbox and the engine. Adjustment is carried out by lengthening or shortening the push rod. Some manufactures have adjustments between the slave cylinder and the clutch folk (underneath the vehicle) while others have adjustments between the top of the clutch pedal and the master cylinder, and others require replacement of the rod with shorter or longer, depending if the clutch is engaging to low or too high. If the clutch is slipping it will probably be too late for adjustment and require replacement of the clutch plate and possibly the clutch cover (pressure plate) and maybe the thrust bearing, Regards John

Apr 16, 2014 | 1990 Dodge Dakota

1 Answer

Put a cluth in a 1991 toyota mr2 turbo 2.0 and its still grinding when I shift gears.. what can I do to solvve my problem


have you replaced your fly wheel and release bearing when you changed your clutch disc?

if yes, then replace your transmission fluid.
also, if you know hot to adjust your clutch release, adjust it. adjust it in a way that you need to draw back your clutch pedal a little higher for the clutch to complete engage.

here are some ways to adjust your clutch.

1. for clutch using clutch cable. open your hood, locate for the transmision, and there you can see a cable that connects the transmision and the clutch pedal. loosen in up a little.
2. for hydrovac clutch with self correcting features. just pull your clutch pedal away from the floor for a few seconds and its done.
3. for hyrovac without self correction. manually adjust the push rod (metal rod that connects the clutch pedal to the clutch master)

Aug 08, 2011 | Toyota MR2 Cars & Trucks

2 Answers

I cannot get the car into gear. It is a manual transmission. Is there a spot where fluid goes in for the clutch?


Your clutch is not hydraulic but is supposed to self adjust. Try the procedure below to help it adjust. If it will not adjust, the clutch may be worn out.


ADJUSTMENT

Free-Play See Figures 8, 9 and 10
The clutch free-play is adjusted automatically by a built-in clutch control mechanism. This device allows the clutch controls to self-adjust during normal operation.
The system consists of a spring-loaded gear quadrant, a spring-loaded pawl and a clutch cable which is spring-loaded to preload the release lever bearing. This compensates for movement of the release lever, as the clutch disc wears. The pawl, located at the top of the clutch pedal, engages the gear quadrant when the clutch pedal is depressed and pulls the cable through its continuously adjusted stroke. Clutch cable adjustments are not required because of this feature.
jturcotte_253.gif

Fig. Fig. 8: Clutch self-adjusting system component identification for the 3.8L engine


CHECKING ADJUSTMENT
The self-adjusting feature should be checked every 5,000 miles (8,000 km). This is accomplished by ensuring that the clutch pedal travels to the top of its upward position. Grasp the clutch pedal with your hand or put your foot under the clutch pedal, and pull up on the pedal until it stops. Very little effort is required (about 10 lbs./4.5 kg). Finally, depress the clutch pedal and listen for an audible "click.'' If you hear a sound, the clutch was in need of adjustment, and it has just adjusted itself.

Nov 23, 2010 | 1998 Ford Mustang

1 Answer

The clutch pedal on Suzuki vitara two litre V6 1998 goes to about inch of floor before activation. Clutch does not slip just too much pedal travel. Is it possible to adjust it? ...


prev.gif next.gif Clutch ADJUSTMENTS 1997-98 Models CLUTCH PEDAL HEIGHT The clutch pedal height should not be a periodic adjustment but may be checked after components of the mechanical clutch system have been replaced. The proper clutch pedal height should be 0.2 in. (5mm) above the brake pedal height If adjustment is necessary, loosen the locknut and turn the adjusting bolt until the appropriate height is reached. Once set, keep the bolt from turning and tighten the locknut to secure the adjustment. CLUTCH PEDAL FREE-PLAY The clutch pedal free-play should be checked from time-to-time in order to assure proper clutch operation. The proper clutch free-play should be 0.6-1.1 in. (15-25mm). Fig. 1: Pedal free-play is adjusted at the joint nut (2), while keeping the outer cable nuts (3) tightened around the center cable thread portion 7924hg30.gif
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. If the free-play must be adjusted, turn the joint nut (2) located at the transmission end of the clutch cable in or out, as necessary to achieve the proper play.
  3. Once the correct pedal free-play is obtained, check the free-play on the release arm (c), it should be 0.02-0.06 in. (0.5-1.5mm).
1999-01 Models These vehicles are equipped with a hydraulic clutch system. No adjustment is necessary.

Nov 05, 2010 | 1999 Suzuki Vitara

2 Answers

Is clutch cable in 2003 Santa fe adjustable? My clutch is going.


u do not have a clutch cable, the system uses a hydraulic clutch release, it is self adjusting, when the clutch starts to slip or engage high on the pedal the clutch is worn out, average cost to replace this clutch isw around $600 on this SUV

Oct 05, 2009 | 2003 Hyundai Santa Fe

3 Answers

1991 Toyota pickup 4WD clutch slipping


There is an adjustment for the clutch pedal under the dash where the push rod goes thru the firewall. There is only aprx. 1/2" of adjustment so be careful when making an adjustment, if your clutch is slipping then you need to shorten the throw of the push rod.

May 06, 2009 | 1991 Toyota Pickup

2 Answers

My clutch is slipping on my 1993 toyota truck. Are there adjustments I can make myself. I am fairly handy, but not a car repair expert.


Sorry, there are no adjustments on your vehicle., The clutch is activated via hydraulic pressure. The master and slave cylinders are "self-adjusting". If the clutch is slipping, you are going to need to pull the trans and replace the clutch assembly. Changing the hydraulics will not help a slipping clutch at all.

Thanks for choosing FixYa for advice!

Mar 05, 2009 | 1993 Toyota Pickup

2 Answers

Clutch slipping


first i would try adjusting the clutch cable because commonly people with think that they're clutch is going out when really just the cable has gotten stretched....try adjusting that first and if that works then you should be fine for another couple thousand miles but if you want to not have to worry bout it for awhile i would just replace teh clutch assembly....usually ranges from $200 to $450 depending on the clutch set and the mechanic that does the work for you. Let me know what happens. :)

Oct 01, 2008 | 1990 Peugeot 405

2 Answers

Jetta clutch


The clutch cable for your vehicle is an auto adjust clutch cable... assuming it is using oem equipment. if you tension seems incorrect you may want to pick up this Manual adjust clutch cable http://www.germanautoparts.com/Volkswagen/Jetta/Clutch/39/11 the auto adjust ones tend to go out and ruin your clutch. the manual adjust is a direct swap out for the auto adjust. if you need info on how to install please reference this site http://forums.vwvortex.com/zerothread?id=1569293

Jun 18, 2008 | 1995 Volkswagen Jetta

Not finding what you are looking for?
1990 Daihatsu Charade Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...