Question about 1995 Jeep Grand Cherokee

1 Answer

I bought a brand new starter, and it is not starting. The lady at Advanced Auto Parts told me it was a positive, or negative wire that runs from the battery to the starter. I don't have a clue what they are talking about. So could you please help me out? Thank you!!!!!!!!!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

This is your car YES or NO

Posted on Mar 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Freightliner wiring diagrams


If you are running a 24 volt starter with two 12 volt batteries
Battery one negative to ground on the vehicle. positive to negative post on battery two and positive on two to the starter.

Aug 21, 2014 | Cars & Trucks

3 Answers

Son's 2001 jeep grand cherokee V8, he just bought it with 110000 miles, and now it clicks but won't start. It has battery power, all lights work and did start once. I assume we need a new starter and...


Just because the lights work does not ensure that the battery is good. To be sure that the battery is good it should be load tested. Most auto parts stores will do this for free, it could save you the trouble and expense of replacing the starter.

Also thouroughly inspect the cables/connectors, make sure they aren't corroded or damage.

This is the starter replacement procedure.

  1. Remove or disconnect the following:
    • Negative battery cable
    • Starter mounting bolts
    • Starter solenoid harness connections
    • Starter
    To install:
  2. Connect the starter solenoid wiring connectors.
  3. Install the starter and tighten the bolts to the following specifications:
    • 2.5L engine: 33 ft. lbs. (45 Nm)
    • 4.0L engine: Upper bolt to 40 ft. lbs. (54 Nm) and lower bolt to 30 ft. lbs. (41 Nm)
    • 4.7L engine: 40 ft. lbs. (54 Nm)
    • 5.2L and 5.9L engines: 50 ft. lbs. (68 Nm)
  4. Install the negative battery cable and check for proper operation.

Mar 24, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I have a gmc 1998 turbo diesel that cranks but wont turnover or try to..i have replaced the supply pump as well as the inline pump..what can i do to get my truck started ..thank you ?


TURN OFF RADIO FIRST TO KEEP FROM LOCKING IT OUT WHEN YOU DISCONNECT NEGATIVE BATTERY CABLE. SOUND LIKE WEAK BATTERY OR STARTER MAKE SURE BATTERY CABLES CLEAN AND TIGHT.IF BATTERY GOOD REPLACE BATTERY CABLES.CHECK STARTER MAKE SURE STARTER SOLENOID AND STARTER OKAY.YOU CAN HAVE THEM TESTED AT AUTO PARTS STORE OR USE A REMOTE SWITCH.REMOVE STARTER FROM VECHICLE USE JUMPER CABLES.HOOK NEGATIVE GROUND CABLE TO BATTERY NEGATIVE THEN GROUND STARTER BODY WITH NEGATIVE BATTERY JUMPER CABLES HOOK POSITIVE JUMPER CABLE TO BATTERY POSITIVE AND STARTER POSITIVE TERMINAL.THEN HOOK REMOTE SWITCH TO STARTER STARTER SWITCH AND OTHER REMOTE WIRE TO STARTER POSITIVE TERMINAL.PRESS REMOTE STARTER WILL SPIN IF GOOD.MAKE SURE INJECTION PUMP STATIC AND DYNAMIC IS TIMING CORRECT BEFORE STARTING TRUCK.

Dec 07, 2010 | 1998 GMC Sierra

1 Answer

Where is the starter located on a 2002 Chevy Suburban? How do I replace it?


    Removing the Starter
  1. Step 1 Open the hood to access the engine compartment. Disconnect the battery by unscrewing the positive and negative terminals. This will prevent the risk of electrical shock.
  2. Step 2 Crawl under the passenger side of the truck and locate the starter. The starter is positioned between the transmission and the engine.
  3. Step 3 Unbolt the negative and positive wires from the starter with a socket wrench. Take the nut off the stud and pull the wires off the stud. Repeat the same for the positive wire.
  4. Step 4 Unscrew the two bolts holding the starter to the frame. Wiggle the starter to work it free from the flywheel.
    Installing the Starter
  5. Step 1 Position the new starter onto the frame. Tighten the bolts to secure the starter in place.
  6. Step 2 Unscrew the nut on the positive stud and push the positive wire down on the stud. Tighten the nut on the stud to secure the positive wires.
  7. Step 3 Unscrew the nut on the negative stud. Push the negative wire on the stud and tighten the nut to the stud to secure the wire.
  8. Step 4 Connect the battery cables to the terminals. Ensure the positive wire connects to the positive terminal. Ensure the negative wire connects to the negative terminal.
  9. Step 5 Start the truck to ensure the starter is functioning correctly. The starter should catch as soon as you turn the key and start the truck.

May 23, 2010 | 2003 Chevrolet Suburban 1500

1 Answer

Alright, bought a 1989 Jeep Cherokee. Replaced


buy a hains manual from an auto parts store

May 10, 2010 | 1989 Jeep Cherokee

1 Answer

My 98 pontiac grand am wont turn over it makes 1 click thats it .is my starter bad ?and where is the stater on the car


The problem doesn't need to be the starter; the first thing you should eliminate is the chance that the problem is only poor contact at the battery terminals, the point where the negative cable is attached (either body sheet metal or engine block) and the starter terminal itself.
You can buy a tool for cleaning battery terminals at any auto parts store or, if the battery has side terminals, use any wire brush. - Disconnect the negative terminal from the battery first. - Then remove the positive terminal. - Clean all parts throughly. - Reattach them. - Try starting the engine.
If it doesn't start; - Disconnect the negative terminal again. - From under the car, locate the starter; it will be at the junction of the engine and transmission and it will have one end obviously butted against the transmission housing. - Remove the heavy cable from the starter and clean the cable end and the starter terminal. - Reattach the cable to the starter. - Reattach the negative battery terminal. - Try starting the engine.
If it still doesn't start, it may still be only a drained battery so find someone to 'jump' your battery and try to start the engine again. If it still doesn't start, then the starter could be bad.
I've had pretty good luck with rebuilt starters and these will cost far less than new.

Nov 11, 2009 | 1998 Pontiac Grand Am

1 Answer

There is no ignition when key is fully inserted and turned to on position. The battery and alternator are in very good shape. It looks like I need a new ignition. Might I need a starter too, or is...


How did you come to the conclusion that you need a new ignition? I assume you mean you need a new ignition switch and not a complete ignition system including coil, distributor, etc. Do a quick test. When you turn the key to the run position, several lights on your display will come on. If you turn further to the start position, those lights should go off, and the starter motor should spin. If you have lights in the run position and the lights go off in the start position, your ignition switch is ok. The problem becomes the starter activation circuit.

Next, check that the start fuse is not blown. Also, ensure the fusible link is not burnt.

Finally, to test the starter, either remove it from the car and take it to your local auto parts store for testing, or get an assistant to help you. To test the starter in the car, get a voltmeter or test light. Attach the negative lead to the car ground. Verify that you have voltage on the starter terminal (the one with the big wire). If yes, place the positive lead on the solenoid terminal. Have your assistant turn the key to the start position. Your test light should illuminate or you should read 12V on your meter. If so, replace the starter. If not, find out where the wire is broken so you are not getting voltage to the solenoid.

Oct 12, 2009 | 1999 Saturn SL

1 Answer

Need brake circuit diagram for 1991 chrysler new yorker


Hi,
1991 Chrysler New Yorker Auto Security Wiring Diagram
Battery Constant 12v+ Positive Wire (+): Red and Pink
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Yellow
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Dark Blue
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Black/Orange
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Black/Yellow
Parking Light Positive Wire Location: In Drivers Kick Panel

Power Door Lock Positive Wire (+): Orange/White Or Orange/Violet
Power Door Lock Positive Wire Location: In Drivers Kick Panel

Power Door Unlock Positive Wire (+): Pink/Violet
Power Door Unlock Positive Wire Location: In Drivers Kick Panel

Door Trigger Negative Wire (-): Yellow
Door Trigger Negative Wire Location: In Drivers Kick Panel

Dome light Supervision Wire: Use Door Trigger (Requires Relay)
Dome light Supervision Wire Location: N/A

Trunk Release Positive Wire (+): Black/White (Requires Relay)
Trunk Release Positive Wire Location: At Trunk Release Switch

Horn Negative Wire (-): Black/Red
Horn Negative Wire Location: At Relay In Fuse box

Tachometer Wire Negative Wire (-): Black/Gray
Tachometer Wire Negative Wire Location: At Ignition Coil

Brake Light Positive Wire (+): White
Brake Light Positive Wire Location: At Switch above Brake Pedal

Factory Alarm Disarm Wire (-): Light Green/Orange
Factory Alarm Disarm Wire Location: In Drivers Kick Panel

Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A


Thank You for contacting Fixya.com

Aug 03, 2009 | 1991 Chrysler New Yorker

2 Answers

My car will start sometimes and then other times I have to keep


If your here just one click when you turn the key to start then i suspect you have a starter going bad.If you heard several clicks while turning the key over once then that would be a weak battery.:)

Jul 23, 2009 | 2000 Mitsubishi Eclipse

1 Answer

It won't Start at all when the car is hot.


take to a local rebuilder and tell them the problem you arent gettin enough voltage to the start pin on the starter

Sep 15, 2008 | 1990 Toyota Camry

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...