Question about 1992 Dodge Dakota

1 Answer

Torque specs for 3.9l engine cylinder head and crankshaft bolts.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Page 3-26 of Chilton's reads:
14. Using no sealer whatsoever, install the new head gasket(s) to the block. Clean, dry and lightly oil all head bolts threads. Install the heads and install the head bolts.

Tighten head bolts in sequence to 50 ft. lbs. (68Nm). Repeat the sequence retightening the bolts to a final torque of 105 ft. lbs. (143 Nm) and repeat the second step to ensure that all bolts are accurately torqued.

torgue chart from chilton (page 3-11) for your engine and year show:
main bearing bolts 85 ft lbs
rod bearing bolts 45 ft lbs
crankshaft damper bolts 135 ft lbs
flywheel bolts 55 lbs

Posted on Mar 27, 2011

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

  • 98 Answers

SOURCE: how to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Which motor?

Posted on Sep 04, 2008

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Cylinder head to engine block torque sequence and ft lbs


    images for Cylinder head to engine block torque and ...
    More images for Cylinder head to engine block torque and sequence

    Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

    boxwrench.net/specs/chevy_sb.htm
    their specs. Click Here! 3/8 Connecting Rod Bolt, Engine Oil, 45 ft-lbs. 11/32 Connecting Rod Bolt, Engine Oil, 35 ft-lbs. Cylinder Heads. Engine oil. (blind hole).

    [PDF]

Nov 29, 2015 | Cars & Trucks

1 Answer

On a 3.8L what is the aspec diagram and tourque for the racker arm


Hi Juan, I'm AL the owner of Big As Auto Repair

Below is the torque specs for the rocker arm as you requested.

SPECIFICATIONS - TORQUE

DESCRIPTION N·m Ft. Lbs. In. Lbs. Camshaft Sprocket-Bolt 54 40 - Camshaft Thrust Plate-Bolts 12 - 105 Forged Connecting Rod Cap-Nuts 54 +¼ turn 40 +¼ turn - Cracked Connecting Rod Cap-Bolts (Refer to 9 - ENGINE/ENGINE BLOCK/PISTON & CONNECTING ROD - INSTALLATION) Crankshaft Main Bearing Cap-Bolts 41 +¼ turn 30 +¼ turn - Crankshaft Main Bearing Cap Cross Bolts (3.8L) 61 45 - Crankshaft Oil Seal Retainer Rear-Bolts 12 - 105 Crankshaft Damper-Bolt 54 40 - Cylinder Block Drain Plugs 20 15 - Cylinder Head-Bolts (Refer to 9 - ENGINE/CYLINDER HEAD - INSTALLATION) Cylinder Head Cover-Bolts 12 - 105 Flex Plate to Crankshaft 88 65 - Engine Mounting (Refer to 9 - ENGINE/ENGINE MOUNTING) Powertrain Torque Strut 54 40 - Exhaust Manifold-Bolts 23 - 200 Exhaust Crossover Pipe-Bolts 54 40 - Intake Manifold - Lower-Bolts 23 - 200 Intake Manifold - Lower Gasket Retainer-Bolts 12 - 105 Intake Manifold Upper-Bolts 12 - 105 Lifter Yoke Retainer-Bolts 12 - 105 Oil Filter Attaching Fitting 54 40 - Oil Cooler Attaching Fitting 27 20 - Oil Filter 20 15 - Oil Filter Adapter-Bolts 28 - 250 Oil Gallery Plug 27 20 - Oil Pan-Bolts 12 - 105 Oil Pan Drain-Plug 27 20 - Oil Pressure Switch 23 - 200 Oil Pump Cover Plate-Screws 12 - 105 Oil Pump Pick-up Tube-Bolt 28 - 250 Oil Dipstick Housing-Bolts 48 35 - Rocker Arm Shaft-Bolts 23 - 200 Spark Plug 16 12 - Thermostat Housing 12 - 105 Timing Chain Case Cover -M8 Bolt 27 20 - -M10 Bolt 54 40 - Water Pump-Bolts 12 - 105 Water Pump Pulley-Bolts 28 - 250
Should you need extra help visit my website here: http://www.bigasautorepair.com/

Apr 15, 2015 | 2005 Chrysler Pacifica

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

I need too know the torque specs on head bolts and crankcam 2.4 engine


on a 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten the cylinder head bolts 90 degrees, starting at the inner 2, and working outward.I dont thin anything has changed on this engine since then.

Mar 19, 2013 | 2005 Toyota Camry XLE

1 Answer

Engine torque settings


Commonly Asked Torque Specs in foot pounds
The main bolts have a torque of 76 lb.-feet and the cylinder head bolts have 62 lb.-feet of torque. The cylinder head studs have 70 foot-lbs of torque, the cam timing gear have lb.-feet of torque, and the cam bearing bolt has 14 lb.-feet of torque.

Crankshaft Torque Specs
  • The stock rod bolts have 46 lb.-feet of torque and the ARP rod bolts have 50 lb.-feet of torque. The crankshaft pulley has 116 lb.-feet of torque, while the flywheel has 80 lb.-feet of torque.


Other Torque Specs
  • The intake manifold and exhaust manifold have 33 lb.-feet of torque each and the oil pan bolts have 9 lb.-feet of torque. The cam timing gear has 58 lb.-feet of torque and the cam bearing bolt has 14 lb.-feet of torque. One set of timing cover bolts have 9 lb.-feet of torque and another set has 29 lb.-feet of torque

Nov 07, 2012 | 1994 Toyota Corolla

1 Answer

I need torque specs. for rod bearings and main bearings for 3.8L GM engine 1979 to 1981


FOR 1979 ROD BEARINGS TORQUE IS 40 FT LBS MAIN BEARINGS 100 FT LBS. FOR 1981 MODELS. ROD BEARINGS TORQUE IS 40 FT LBS. AND MAIN BEARINGS 100 FT LBS. CYLINDER HEAD BOLTS 80 FT LBS. CRANKSHAFT PULLEY BOLT 225 FT LBS. FAN PULLEY TO BALANCER 20 FT LBS.

Jun 02, 2011 | Buick Century Cars & Trucks

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1992 Dodge Dakota Logo

3,483 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...