Question about Isuzu Trooper

1 Answer

Flywheel and presser plate torque specs for a 1991 isuzu trooper with 2.8l v6

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 176 Answers

The flywheel bolts call for 52 lb-ft, the pressure plate calls for 13 lb-ft. Tighten in a diagonal pattern, one or two times at a time until seated then apply the final torque.
I have attached an image for reference. Goodluck
flywheel and presser plate torque - txtexan_2.gif

Posted on Mar 27, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I replace the heater core in my 1994 Isuzu Trooper?

You will get your solution and all info on service info, repair info, parts info, wiring/electrical/fuse diagrams, error/fault codes, torque specs, PCV,

owner's/service/repair/parts/maintenance manuals etc everything
this website
it's a very good website for vehicle problems even as old as 1991 ford..

Mar 16, 2018 | 1994 Isuzu Trooper

1 Answer

How do you remove the torque converter bolts on a 1999 Isuzu trooper

all A/T trans have and inspection port on the trans bell lower.
this allows you to remove said , flex plate bolts..
2wd or 4wd.
i guess you are lost at this step here, in red circle.
it says flywheel under covers off... see that?

Nov 07, 2016 | 1999 Isuzu Trooper

1 Answer

? looking the bolt tension specs for flywheel and clutch pressure plate for 4hf1 thank you

Torque Specification - National Truck Spares ' Parts
1073, 4BC2 tq, Isuzu, Torque Specification, KT26 TLD57 NKR57 NPR57 ... 1075, 4HF1Tq, Isuzu, Torque Specification, NKR66 NPR66, 92 - 03, 4HF1, 4334

Small Block Chevrolet V8 Engine Specs ' Torque Specs ...
Flywheel (Clutch). Thread Locker, 60 ft-lbs. Clutch Pressure Plate, Thread Locker, 35 ft-lbs. Centerbolt. (Harmonic Damper). Engine Oil, 60 ft-lbs. Bellhousin

Nov 07, 2015 | Cars & Trucks

2 Answers

Isuzu V6 sparkplug firing order

gee guy, 3.1L or 3.2L?
you only need 3 things to time the distrib. static.
where is #1, its the most forward cylinder, LOOK carefully.
forward means closest to the cam drive end of engine.
not flywheel end.
rotor rotation direction (crank and watch it)
now the order, 3.2l v6? IS It? the single cam?
1990 trooper v6
answering for only USA car...
our 3.2 has no distrib V6 its DIS.

3.1L V6 USA spec. only. rotor is CCW

Sep 27, 2014 | 1990 Isuzu Trooper

1 Answer

Need flywheel specs and pressure plate torque specs for 1991 ford f250 460 motor 4x4

flywheel bolt torque 75-85 ft-lbs and pressure plate 15-20 ft-lbs

Apr 08, 2011 | Ford F-250 Cars & Trucks

1 Answer

1990 Isuzu Trooper Flywheel needs to be resurfaced what should the step or the depth of the cup be? 2.6 Liter Engine 4Ze1

The Isuzu Amigo 2.6L 4 cyl , The Isuzu Trooper 2.6L 4 Cyl and the Honda Passport I believe with a 2.6L all have the same 4ZE1 2.6L 4 Cyl engine in them.

As per this page =>, found it looking for the same flywheel "cup" (aka we all call it a "step" but the machinists have a different flywheel that they call stepped so the one attached to the 4ZE1 is "Cupped") . Says the cut spec is .157"-.159" , so in this case the clutch pressure plate bolting surface is .157"-.159" higher then the center flat friction surface that the clutch disc sits in. (it doesn't indicate that it's inches or mm but I assume that because most usa machine shops use thousands of an inch calipers and micrometers it's more then likely inches).

Hope that helps you or anyone out there who needed that info :] .

Nov 28, 2010 | 1990 Isuzu Trooper

1 Answer

2000 Isuzu Trooper Specs

Tighten the connecting rod cap nuts
Torque : 54 N·m (5.5 Kg·m/40 lb ft)

Jun 30, 2009 | 2000 Isuzu Trooper

1 Answer

I need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

867 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

84027 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

Jonah Oneal

Level 3 Expert

14065 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides