Question about Lincoln Continental

1 Answer

Water Pump appears to be "fused" to engine housing. Already removed the four bolts to remove pump, but it will not budge. What am I missing out on doing here?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Lincoln Master
  • 680 Answers

The fan clutch is held on with the large nut that spins with the fan. You have to turn it counter clock wise to loosen it.The four bolts just hold the pulley on. Make sure the belt is still on to keep some tension on the pulley. You'll either have to get the wrench made to remove it, or give it one good shot downward on the passenger's side with a LONG punch or chisel. Then spin it off by hand. Please rate my assistance and thanks for using Fixya.

Posted on Mar 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change water pump on a 1995 crown victoria after you have nothing but the pulley and water pump left and there connected


There should be four bolts between the back of the pulley and the water pump holding the pulley on the water pump. You can either try to remove them before you take the water pump off the engine (not recommended), or remove the four (I think) bolts holding the water pump to the engine block, remove the water pump, ten remove the four bolts holding the pulley to the water pump shaft (recommended). Good luck.

Oct 01, 2013 | Cars & Trucks

3 Answers

How do you replace water pump?


Assuming this is a 460 Ford Big Block:

REMOVAL

-Drain cooling system.
-Remove drive belts.
-Remove bolts attaching fan shroud to radiator.
-Remove fan blade from fan clutch and remove fan shroud.
-Remove fan clutch and water pump pulley from water pump.
-Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Do not remove A/C compressor or power steering pump from A/C compressor mounting bracket.
-Pull A/C compressor mounting bracket forward to remove from stud on water pump.
-Remove bolt attaching generator adjusting arm to water pump. Remove four bolts attaching generator mounting bracket to cylinder head, cylinder block and water pump.
-Remove remaining water pump attaching bolts and remove water pump from engine front cover.
-Remove water pump cover from water pump. Discard water pump housing gasket and water pump cover gasket.
INSTALLATION
-Remove any gasket material from water pump cylinder front cover and separator plate mating surfaces.
-Position new water pump housing gasket and water pump cover gasket coated on both sides with Perfect Seal Sealing Compound B5A-19554-A or equivalent water-resistant sealer meeting Ford specification ESE-M4G115-A.
-Position water pump and water pump cover onto engine front cover. Install bolts and tighten to16-24 Nm (12-18 ft. lbs.).
-Install generator mounting bracket to cylinder head, cylinder block and water pump with four attaching bolts. Install generator adjusting arm to water pump with one attaching bolt. Tighten 7/16-inch bolts to 54-71 Nm (40-53 ft. lbs.) and 3/8-inch bolts to 41-54 Nm (30-40 ft. lbs.).
-Position A/C compressor mounting bracket over water pump stud and secure to cylinder head with four bolts tightened to 54-71 Nm (40-53 ft. lbs.) and secure nut to water pump to 41-54 Nm (30-40 ft. lbs.).
-Install water pump pulley and fan clutch to water pump hub with four bolts. Install fan blade to fan clutch with four bolts. Tighten water pump pulley, fan clutch hub bolts, and fan-to-fan clutch hub bolts to 16-24 Nm (12-18 ft. lbs.). Install fan shroud.
-Install drive belts.
-Fill and bleed the cooling system.
-Start the engine and check for leaks

Jan 10, 2011 | 1997 Ford F350 Crew Cab

1 Answer

How to replace water pump 2003 alero. 3400 engine.


Removal & Installation 2.2L Engine To Remove:
  1. Disconnect the battery ground cable.
  2. If equipped with an automatic transmission, remove the exhaust manifold..
  3. Drain the cooling system.
  4. Raise and safely support the vehicle.
  5. Remove or disconnect the following:
    • Right front wheel and tire assembly.
    • Right front fender liner. chevy_cav_02-04_accescover.gif

    • Access plate on the water pump sprocket from the timing cover.
  6. Install J 43651 water pump sprocket holder or equivalent to the water pump sprocket.
  7. Use the access plate bolts to attach J43651 to the engine front cover.
  8. Remove or disconnect the following:
    • Bolts that secure the sprocket to the water pump.
    • Bolt that secures the engine block to the water pump.
    • Bolt that secures the engine front cover to the water pump.
    • Feed pipe that joins the thermostat housing to the water pump. chevy_cav_02-04_wp.gif

    • 2 Bolts that secure the water pump to the engine block.
    • Water pump.
To Install:
  1. Use a threaded stud in the hub to align the water pump sprocket.
  2. Install or connect the following:
    • Water pump.
    • 2 bolts that secure the water pump to the engine block.
    • Feed pipe that joins the thermostat housing to the water pump.
    • Front cover bolt and the bolt that secures the engine block to the water pump. Tighten the bolts to 15 ft lbs (20 Nm).
    • 2 of the bolts that secure the water pump sprocket to the water pump.
  3. Remove the threaded stud.
  4. Install the last bolt.
    • Tighten the bolts to 89 in lbs (10 Nm).
  5. Remove J 43651.
  6. Install the access plate on the water pump sprocket to the timing cover.
  7. Install the access plate bolts.
    • Tighten the bolts to 18 in lbs (10 Nm).
  8. Install the front fender liner.
  9. Install the right front tire and wheel.
  10. If equipped with an automatic transmission, install the exhaust manifold.
  11. Fill the cooling system.
  12. Connect the battery ground cable.
2.4L Engine To Remove:
Water pump 2.4L 87953070.gif

  1. Disconnect the negative battery cable
  2. Drain the engine coolant.
  3. Remove the exhaust manifold.
  4. Remove the coolant intake pipe as follows:
    1. Remove the coolant inlet pipe bolts.
    2. Remove the wheel and tire assembly.
    3. Remove the engine splash shield.
    4. Remove the bolts from the transaxle-to-engine block brace and remove the brace.
    5. Remove the radiator hose from the coolant inlet pipe.
    6. Remove the coolant inlet pipe to oil pan bolt.
    7. Remove the coolant inlet pipe, thermostat and seal.
  5. Lower the vehicle.
  6. Disconnect the heater hose quick connect from the heater outlet pipe.
  7. Remove the front timing chain cover and the chain tensioner.
  8. Unfasten the water pump-to-cylinder block bolts.
  9. Remove the water pump-to-timing chain housing nuts.
  10. Remove the water pump and cover mounting bolts and nuts.
  11. Remove the water pump and cover as an assembly. Separate the two pieces after removal.
  12. Clean the mating surfaces.
To Install:
  1. Install the water pump cover to the water pump assembly.
  2. Install and hand tighten the pump cover mounting bolts.
  3. Install water pump cover assembly.
  4. Install and hand tighten the cover-to-block mounting bolts.
  5. Install and hand tighten the water pump-to-timing chain housing nuts.
    • Tighten the water pump-to-timing chain housing mounting nuts to 19 ft lb (26 Nm).
    • Tighten the water pump cover-to-water pump mounting bolts to 124 in lb (14 Nm).
    • Tighten the water pump cover-to-engine block bolts starting with the bottom bolt first to 19 ft lb (26 Nm).
  6. Install the heater hose to the water pump pipe.
  7. Using new gaskets, install the exhaust manifold.
  8. Install the oil level indicator and tube.
  9. Connect the brake vacuum tube to the cam housing.
  10. Raise and safely support the vehicle.
  11. Install the catalytic converter.
  12. Install the coolant inlet pipe.
    • Tighten the inlet pipe-to-oil pan bolt to 19 ft lb (26 Nm). Tighten the coolant inlet pipe bolt to 124 in lb (14 Nm).
  13. Install the timing chain and tensioner.
  14. Lower the vehicle.
  15. Connect the oxygen sensor.
  16. Fill cooling system and check the system for leaks.
3.4L Engine To Remove:
  1. Disconnect the battery ground cable.
  2. Drain the cooling system.
  3. Loosen the water pump pulley bolts.
  4. Remove or disconnect the following:
    • Drive belt.
    • Water pump pulley bolts and pulley.
    • Water pump bolts, pump and gasket.
    • Clean the water pump mating surfaces.
To Install:
  1. Install or connect the following:
    • Water pump gasket and pump.
    • Water pump bolts.
      1. Tighten the water pump bolts to 89 in lbs (10 Nm).
    • Water pump pulley and bolt until snug.
    • Drive belt.
  2. Tighten the water pump pulley bolts to 18 ft. lbs (25 Nm).
  3. Fill the cooling system.
  4. Check for leaks.
  5. Connect the battery ground cable.
prev.gif next.gif

Aug 31, 2010 | 2003 Oldsmobile Alero

1 Answer

REPLACE WATER PUMP


3.0L OHV Engine

  1. Disconnect the negative battery cable. Allow the engine to cool.
  2. Remove the radiator cap and drain the cooling system.
  3. Loosen four retaining bolts securing the water pump pulley to the water pump hub.
  4. Remove the accessory drive belts.
  5. Remove the automatic belt tensioner.
  6. Disconnect and remove the heater hose from the water pump.
  7. Remove the engine control sensor wiring from the locating stud bolt, if equipped.
  8. Remove the water pump-to-engine retaining bolts and lift the water pump and pulley up and out of the vehicle.
To install:
  1. Clean the gasket surfaces on the water pump and engine front cover. Install a new gasket on the water pump using gasket adhesive.
  2. Place the water pump in position on the engine with the pulley and four retaining bolts loosely installed on the hub.
  3. Apply pipe sealant to bolt No. 3. Refer to the accompanying illustration for bolt location.
  4. Install the bolts in the water pump housing.
  5. Tighten bolts Nos. 4, 5, 6, 7, 8, 9 and 10to 15-22 ft. lbs. (20-30 Nm). Tighten bolts Nos. 11, 12, 13, 14 and 15 to 71-106 inch lbs. (8-12 Nm).
The bolts are of different lengths and must be installed in the correct locations.
  1. If equipped, attach the engine control sensor wiring to the locating stud bolt.
  2. Hand-tighten the water pump pulley retaining bolts.
  3. Install the accessory drive belts.
  4. Tighten the water pump pulley bolts to 15-22 ft. lbs. (20-30 Nm).
  5. Connect the heater hose to the water pump.
  6. Fill the cooling system. Connect the negative battery cable.
  7. Start the engine and allow it to reach normal operating temperature. Check for leaks and proper operation.

3.0L DOHC Engine
  1. Disconnect the negative battery cable. Drain the engine cooling system.
  2. Remove the water pump drive belt.
  3. Disconnect the radiator and heater hoses from the water pump.
  4. If equipped, remove the A/C compressor-to-water pump brace.
  5. Unfasten the four nuts securing the water pump to the engine and remove the water pump.

To install:

89da3e5.jpg

Fig. : Water pump mounting-3.0L DOHC engine
  1. Clean the water pump to engine gasket sealing surfaces.
  2. Install the water pump using a new gasket and install the four retaining nuts. Tighten the retaining nuts to 15-22 ft. lbs. (20-30 Nm).
  3. Connect the radiator and heater hoses to the water pump. Make sure the clamps are securely tightened.
  4. If equipped, install the A/C compressor-to-water pump brace. Tighten the brace bolts to 15-22 ft. lbs. (20-30 Nm).
  5. Remove the water pump drive belt.
  6. Fill the engine cooling system, then connect the negative battery cable.
  7. Start the engine and allow it to reach normal operating temperature, then check for coolant leaks and proper engine operation.

Hope this helps (remember rated this).

Aug 10, 2010 | 1999 Ford Taurus

1 Answer

Water pump removal


REMOVAL & INSTALLATION
2.0L Engine
  1. Disconnect the negative battery cable.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant.
  1. Drain the engine cooling system.
  2. Raise and safely support the vehicle.
  3. Remove the lower radiator hose from the water pump.
If the lower radiator hose is hard to reach on the back of the water pump, remove the hose at the radiator and after the water pump is ready to be removed, pull the water pump away from the engine block until there is enough room to remove the hose from the pump.
  1. Lower the vehicle.
  2. Remove the accessory drive belt.
  3. Remove the timing belt covers and the timing belt as outlined in this Section.
  4. Remove the four water pump retaining bolts.
  5. Remove the water pump.
To install:
  1. Thoroughly clean all sealing surfaces.
  2. Install a new water pump gasket and the water pump onto the cylinder block.
  3. Tighten the retaining bolts to 12-15 ft. lbs. (16-20 Nm).
  4. Reinstall the timing belt and the timing belt covers as outlined in this Section.
  5. Reinstall the accessory drive belt.
  6. Raise and safely support the vehicle.
  7. Reinstall the lower radiator hose.
  8. Lower the vehicle.
  9. Fill the engine cooling system.
  10. Reconnect the negative battery cable.
  11. Start the engine and top off the coolant as necessary. Check for leaks.


2.5L Engine

Before continuing with this procedure, be sure three new water pump retaining bolts (W701544) are available. Due to their torque-to-yield design, the bolts stretch and cannot be reused.
  1. Disconnect the negative battery cable.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant.
  1. Drain the engine cooling system.
  2. Remove the water pump pulley shield.
  3. Remove the water pump drive belt.
  4. Remove the water pump inlet and outlet hoses from the water pump.
  5. Remove the three water pump to left cylinder head retaining bolts.
  6. Remove the water pump and water pump housing from the vehicle.
  7. Remove the water pump to water pump housing retaining bolts and separate the water pump from the water pump housing.
To install:
  1. Thoroughly clean all sealing surfaces.
  2. Install the water pump to the water pump housing using a new gasket and install the retaining bolts. Tighten the retaining bolts to 16-18 ft. lbs. (22-25 Nm).
  3. Position the water pump and water pump housing and install three new torque-to-yield retaining bolts into the left cylinder head.
  4. Tighten the new retaining bolts to 11-13 ft. lbs. (15-18 Nm), then rotate the retaining bolts 85-95 degrees.
  5. Reinstall the water pump inlet and outlet hoses to the water pump.
  6. Reinstall the water pump drive belt.
  7. Reinstall the water pump shield.
  8. Fill the engine cooling system.
  9. Reconnect the negative battery cable.
  10. Start the engine and top off the coolant as necessary. Check for leaks.


Hope helps (remember comment and rated this).

Jul 07, 2010 | 1996 Mercury Mystique

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

1 Answer

1995 Buick LeSabre with a leaking water pump.


The water pump removal is a breeze on this vehicle. First remove your four bolts that hold the pully to the pump, then remove the serpentine belt. Next remove all bolts from water pump, now the fun part, pry the housing of the water pump off gently trying not to nick or gouge the engines placement for the housing. now all you have to do is make sure the housing is clean of all debris or old gasket material, you wouldnt want any of that gunk getting inside. nowplace your gasket properly on new water pump and place on housing. make sure the gasket fits nicely. reinstall pully to water pumy, reinstall your serpentine belt, place new antifreeze, I prefer the peak green full strength, make sure to mix correctly also. start engine let run for 5- 10 minutes and then let cool down and check levels. hope this helps.

Jan 27, 2010 | 1995 Buick LeSabre

2 Answers

Need the step by step instructions and pictures on how to replace an water pump on an 2002 Oldsmobile Alero 2.4L


Removal & Installation

2.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Exhaust manifold, if equipped with n automatic transaxle Right front wheel Splash shield Water pump sprocket access plate from the timing cover

    fcd00e0.jpg

    Fig. Remove the water pump sprocket access plate from the timing cover -2.2L engine
  5. Attach Water Pump Sprocket Holding Tool J 43651to the sprocket using the access plate bolts to secure the tool to the engine front cover.
    Sprocket to water pump bolts Engine block to water pump bolt Engine front cover to water pump bolt Thermostat housing to water pump feed pipe 2 water pump to engine block bolts Water pump

    30965cd.jpg

    Fig. Water pump mounting-2.2L engine
To install:
  1. Use a threaded stud in the water pump hub to align the hub to the water pump sprocket.
    Water pump and bolts Thermostat housing to water pump feed pipe Engine front cover bolt and engine block to water pump bolt. Tighten the bolts to 15 ft. lbs. (20 Nm) 2 of the water pump sprocket to water pump bolts
  2. Remove the threaded stud.
    Last water pump sprocket to water pump bolt and tighten the sprocket bolts to 89 inch lbs. (10 Nm).
  3. Remove the tool.
    Water pump sprocket access plate to the timing cover and tighten the bolts to 89 inch lbs. (10 Nm) Splash shield Right front wheel Exhaust manifold, if removed
  4. Fill the cooling system.
  5. Connect the negative battery cable.
2.4L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    WARNING Do not rotate the flex coupling more than 4 degrees or damage may occur. Oxygen Sensor (O 2 S) electrical connector Exhaust manifold heat shield Coolant inlet housing bolt through the exhaust manifold Exhaust manifold brace-to-manifold bolt Manifold-to-exhaust pipe studs Coolant inlet housing-to-water pump cover bolt Exhaust pipe from the exhaust manifold by pulling it downward Coolant inlet pipe from the oil pan Brake vacuum pipe from the camshaft housing Exhaust manifold from the cylinder head Heater hose from the heater outlet pipe Timing chain cover and tensioner Water pump cover-to-engine bolts 3 water pump-to-timing chain housing nuts Water pump and cover assembly Water pump cover from the pump

    f9cdfa8.jpg

    Fig. Exploded view of the water pump mounting-2.4L engine
continue...

Oct 22, 2009 | 2002 Oldsmobile Alero

2 Answers

Finding the water pump on 2001 chevy cavalier


Need to know engine size but usually water pump is directly connected to the lower rad hose. Moe

May 15, 2009 | 2001 Chevrolet Cavalier

3 Answers

1998 Ford Escort ZX2 Water Pump Housing removal


I am sure the leak is the water pump based on years of Escort work, The ZX2 is equipped with a 2.0L DOHC V-Tech engine. The water pump is on the front (rt side of car) of the engine block, visible with the hood up. NAPA autoparts replacement instructions are to loosen the belt drive pulley from the pump BEFORE removing the serpentine belt. Once the four bolts are loose, take the belt off (good time to replace?) remove bolts and old water pump (four more bolts)- it will be tight, but it comes out- clean gasket area and install new gasket and pump in reverse order. That includes putting the pulley on and hand tightening the bolts, put on the belt, finish tightening the bolts to the pulley.

Aug 10, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

fordexpert

Level 3 Expert

5572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...