Question about 1986 Ford Bronco II

1 Answer

After putting trany together codes read 41,25,33,77 i then replace distributer cap and rotor, oxgyen sensor,and air charge sensor now it wont start new codes are 14,18.,51,54,33 and doesnt start what now?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 335 Answers

Check your starter solenoid(turn the key to run position then use a jumper wire to connect both large terminals, if starts replace) if no difference, then have your ignition module tested, if its good, then check the ignition switch make sure its operating properly. Also make sure all grounds are in place and attached.

Posted on Mar 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cabrio wont start it will crank but not fire


When you squirt water on plug wires and the car stalls, that means that your plug wires are bad. PLUG WIRES (not rotor, cap, or any sensor).
Replace your spark plug wires with new, and you should be fine.

May 14, 2015 | Cars & Trucks

2 Answers

Engine misses when you excelerate. when its hot engine wont start


It could be to much air, not enough fuel. Or to much fuel, not enough air. Most likely the first, unless you notice a lot of black smoke when accelerating. Check engine light on? Also could be the catalytic converter/s. Have the codes read. repost.

Dec 12, 2014 | 2000 Nissan Quest

1 Answer

1992 c1500 will crank but wont start


check for spark if you do not have spark and thie problem u are having now is the same as original problem it is most likely the ignition module also check to make sure distributer shaft / rotor turns while cranking also check rotor if it is burnt it can cause this also check for moisture under distributer cap if wet spray with brake clean and air dry

Mar 25, 2012 | 1992 Chevrolet C1500

1 Answer

2000 infiniti QX4 3.3L (engine has a distributer) stalls out especially when revved from idle. Also won't start or very difficult to start, haven't been able to get it to start for a couple days...


pull one ignition cable out of cap just enough to see the tip of connector and crank it, a spark should jump from cap to tip of wire. no spark means you need the whole distributor replaced. buy it from nissan or infiniti dealer, it comes with cap rotor installed and 12 mo 12k mile warranty, no matter who installs it. dont waste time with aftermarket rebuilt distributor, those are not reliable. https://parts.infinitiusa.com/

Apr 06, 2017 | Infiniti QX4 Cars & Trucks

2 Answers

Where is the crankshaft position sensor located on a 1994 Cadillac Sedan Deville 4.9L V8? I need a diagram or illustration or something. Thanks.


Your 4.9 has a distributor, correct? If so, it does not have a crank sensor, per se, it has a hall effect sensor in the base of the distributor, also called a coil pickup, just below the rotor. It has a harness that goes through the distributer housing.cap and plugs into a harness, and is pretty easy to replace.

Jan 25, 2011 | Cadillac DeVille Cars & Trucks

2 Answers

1998 GMC Sierra 2500 5.7L hard cold starts last month, now won't start cold w/o a little carb cleaner in intake. Codes for oxy sensors, mass air sensor and crank/cam position. Drove today, no power just...


starting definately has a lot to do with the crank/cam position sensors, but it wouldnt have nothing to do with hot or cold weather, oxygen sensor will make the vehicle run too rich if its out, you will smell fuel very strong out the exhaust, that could make it run sluggish also, and usually if the mass air flow sensor goes out the vehicle wont start at all...

Nov 27, 2010 | 1998 GMC Sierra

2 Answers

Just replaced engine in my 97 its a vortec brought it to tdc put in distributar it turns over and tries to start but wont i turn it just a little it acts better but i cant move it far enough


take the spark plug out of the #1 cylinder and turn the engine by hand until the piston is at the top dead center of its stroke (put a screw driver in the hole and you should be able to tell when its all the way up). now pull the cap off the distributer the rotor should be pointing at the #1 cylinder wire. if not then the distributer is in the wrong possition. remove the distributer and point the rotor in the correct possition(#1 cylinder) and place the distributer back in.also if this is a used engine replace the cap,rotor plugs and wires.the truck should start. Hope this helps you out.

Mar 14, 2010 | 2002 GMC Sierra C/K1500

1 Answer

99 gmc Safari awd 4.3L when it rains engine cranks wont start no codes found backfired so bad it blew the muffler apart at the seams. has new distributer, upper manifold and new upgraded multiport fuel...


This may be due to a bad coil wire shorting out GM had many problems with these ..There was even a recall for this a long time ago.. The wire would short out on the metal foil on the doghouse and the aluminum a/c line if there was any damage or corrosion to the terminals...A new distributor ...I had an apprentice put one in one time and he thought the rotor was to point to #1 and forgot the dist cap was like a printed circut board and the rotor was no wheres near #1 good luck

Jan 27, 2010 | GMC Safari Cars & Trucks

1 Answer

NO SPARK PUT A NEW COIL ON DID NOT FIX TOOK IT TO A GSRAGE SAID IT NEEDED A CRANK SENSOR CAM SENSOR WIRES PLUGS DIST CAP AND ROTER RAN ONE DAY NOW THEY SAID A HOLE DISTRIBUTER AND A TIMEING BELT.I REALLY...


If you are sure they said, a distributer cap a roter and a distributer, there is a problem! Because on a 1998
plymouth, there is no distributer or cap or roter.
Your cam sensor along with the crank sensor-temp sensor and a few other sensors, send a signal to the
powertrain control module, that sends a signal to the
coil pack(that you said was replaced) that fires the
spark plug. I would hold off from having any further
work done there, until you can check out what they
say they have already done. Ask if you can have the
old parts they replaced so far. You will want to have
an OBDII scan test done, to see what codes come up. It should have one of the first tests they did.
If I have read your post correctly, have them write an
estimate for what they will replace next. This info. is
based on the car being a 1998 plymouth and not a
1988 I would not wan't to acuse somone of anything
based on a typo. Hope this helps. Good luck.

Jan 25, 2010 | 1998 Plymouth Voyager

2 Answers

Hi ,I have a chevy blazer s-10 1993 and she won't start ,I change :spark plugs ,cap ,rotor , spark plug wires, fuel pump (58 psi) injectors (spider)internal hoses, starter and battery. but still my truck...


Find the pressure test port (looks like a tire valve) on the fuel distribution rail over the injectors and place a can over the open end of the valve. Press the inner pin to release fuel into the can. If the pressure seems to fall rapidly, replace the fuel filter. Is the check engine light on? Rent a scanner, read any code(s), and pursue to repair(s). A bad crankshaft sensor or camshaft sensor can prevent the injectors from firing fuel into the engine.

Sep 14, 2009 | 1993 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...