Question about 1984 Chevrolet S-10

1 Answer

C@yahoo.comhow do i identify my carburator 1984 2.8 chevy s10 blazer

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,002 Answers

GM uses an eight digit number to identify their Rochester carburators. It should be stamped into the metal on the float bowl area. It should be on the linkage side. If it is the original carb on the truck it will likely start with the number 1708---- or possibly 1707----. Any time I went looking for the carb number it usually took a few minutes to locate and read it. They didn't exactly kill themelves making it easy to read. Take a rag and wire brush with you to clean off the grime as well as a can of spray cleaner or penetrating fluid. A flashlight would be a big help too. You need this number to order rebuild kits and to set it up after. Hope this helps.

Posted on Mar 27, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is evap cantister on a 2000 chevy blazer

They used to be in the engine compartment
near the front--on S10

I'm driving an old 1984 --so things may have changed,
but they only go to 2004 then stop making them

Nov 29, 2012 | Chevrolet Blazer Cars & Trucks

1 Answer

I need the wiring layout for an 1984 chevy s-10 ignition module

Got an 84 shop manual with wiring

What do you need ?

Also got a 1984 S10 Blazer since new

Oct 08, 2010 | 1984 Chevrolet S-10

1 Answer

I need a diagram on the fuse book on a 1984 S10 Blazer

go to diagram

Oct 06, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

1985 Chevy s10 2.8L every time I go above 25mph it dies. I have changed out the fuel pump and fuel filter. But the problem is still there. Any ideas. It is carburate. And the fuel lines look good

I would have the carburator checked/replaced because while the lines look good, it may not be giving the engine the right amount of gas it needs to do anything above 25.

Oct 22, 2009 | 1985 Chevrolet S-10 Blazer

1 Answer

Wiring Diagram

Chevy S-10 Blazer Ignition Control (IC) Circuit Wiring Diagram62566385.gif

May 20, 2009 | 1983 Chevrolet S-10

1 Answer

How do you adjust the fuel air ratio in the carb on a 1985 s10 chevy blazer?

The carbureator is sealed so you cannot get into to make adjustments. That said, there are soft lead plugs near the base and you can pry them out. Now you are able to access the adjusting screws. You need an air/fuel meter to accurately set them to spec. Hope this helps.
RPM Northwest

Jan 26, 2009 | 1985 Chevrolet S-10 Blazer

1 Answer

1984 s10 2.8 manual trans. flywheel causes engine to vibrate

no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Jan 16, 2009 | 1984 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides