Question about Kia Rio

1 Answer

The air in my car will only work on 1. However, if i push it in on 2,3,4 it will work.

Posted by on

  • HBUCKO824 Dec 13, 2008

    I NEED TO CHANGE THE BLOWER MOTOR RESISTOR IN MY KIA SORENTO, WHERE IS IT?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 183 Answers

If you are talking about the blower motor speed switch.It comes on any speed if you apply a little force? If so,replace it.Its bad..Good Luck!!!

Posted on Aug 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My heater blower only works on top two numbers but don't work on 1 & 2 do you know what the problem is ?


The most common cause of a heater and air conditioner blower not working on a car is a faulty blower motor. Without the blower motor, the system is unable to push air through the vents inside the vehicle.

Kamagra Kaufen http://kamagra-billig.com/

Oct 03, 2016 | Cars & Trucks

1 Answer

Remote control has stopped working. Have tried changing the battery of the remote control but that did not work.


Does the red light on the remote light up when you push any of the button
if no, replace remote
if yes, then try repograming the remote to the car again.
-Have remotes' ready. if you have two then fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 8)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes' should work again.
good luck

Dec 17, 2010 | 2003 Honda Accord

2 Answers

Both key fobs for honda pilot 2006 no longer works. Do I need new keys or is it something internal such as a fuse?


First thing, does the red light on the remote light up when you push any of the button
if no, then replace battery inside remote
if yes, then try repograming the remote to the car again.
-Have both remote ready. fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 7)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes should work again.
good luck

Dec 17, 2010 | Honda Pilot Cars & Trucks

2 Answers

Need to restart diesel engine after running low on fuel, on a 2003 Chevy Silverado 2500HD


After putting more fuel in the vehicle
Open the hood
On the righthand side of the engine just to the side of valve cover, back by the firewall you will find a round plunger about 1 1/2" in diameter. The plunger will push down and come right back up on its own. Push the plunger rapidly till the pushing gets firmer or stiff.
Start it up. Sometimes it will have to be done a couple of times. I actually fined it works best to pump it firm and then have someone else start it while you keep pumping it. If you do it this way make sure your body is clear of all moving parts.
This is a very fast way of getting it going
Good luck

May 06, 2010 | 2003 Chevrolet Silverado 2500HD

1 Answer

How to change air filter on a 1999 ford taurus


Release the 2 clips holding the air box lid on and slide the lid up pull out the old 1 make sure its clean under the filter and slide a new 1 in until it seats in the grove and push the air box lid back down and clip it shut.

Jan 11, 2010 | 1999 Ford Taurus

1 Answer

Toyota brake problem


the prob is still your master cylinder. the seal sounds like its back on its self or there is a wear line that pushes it back, get 1 from a scrapy that works, fit undo the rear nipples and leave to drip for 5 mins . then do the front, look at the rear load compensator some vehicles have a bleed nipple to release trapped air from there, what happens when nipple open and u push pedal.

Aug 16, 2009 | 1987 Toyota Corolla 2 Door

3 Answers

My brake resevoir is the same as my clutch..it doesn't leak but I have to pump clutch peddle to shift. What do I do? Is It my clutch plate or what...


The wear on your clutch plate is increasing the distance your actuator piston has to push, so your correct about needing some clutch parts soon.

Jul 09, 2009 | 1996 Ford Escort 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...