Question about 1998 Volkswagen Jetta

1 Answer

Won't turn over and marker lights blink several times

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volkswagen Master
  • 5,763 Answers

This sounds like the alarm is active, use the key and lock and unlock the driver door and that should turn the alarm off, also make sure the battery is good and fully charged. good day.

Posted on Mar 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Toyota corolla 1.8, how do I get my passenger front turn signals to work? What wires have to be connected together for my turn signal and side corner marker to work?


does your car have the signal light flasher if so find it and replace it also check the fuses maybe both sides are fused separate

May 05, 2017 | 1994 Toyota Corolla

1 Answer

2002 TrailBlazer side marker lights blink with 4ways


I think you either have a defective bulb socket or you still have a ground problem, that is the only thing that can cause this, the ground issue may be caused by the turn signal switch as well.

Apr 12, 2017 | 2002 Chevrolet TrailBlazer

2 Answers

Check engine light flashes car won't start


you can get the trouble codes out by turning key on off on off on then watch the check engine light it will flash a number of times n pause this will give you codes to take to the auto parts store n tell them they will know most of them the service writer at the dealer can find the rest (example) blink blink blink pause blink blink =32 there could be several so do it a couple times to make sure you get them right and get them all

Mar 15, 2012 | 1992 Plymouth Acclaim

1 Answer

How to replace passenger turn signal bulb


The side marker light must be removed in order to get at the turn signal light.
There are two screws holding the side marker light which is situated above the turn signal.
Open the hood.
Remove the phillips head screw at the top of the side marker light.
Using a long #2 Phillips screwdriver, remove the screw on the outside of the side marker light. This can be seen by looking between the lower side of the side marker light and the top side of the turn signal.
The side marker can be moved.
The turn signal has one screw on the top of the fixture that must be removed.
Slide out the turn signal fixture. There is a small feature on the lower front corner of the turn signal fixture that you must note to properly reinstall the turn signal.
In order to get to the bulb, rotate the bulb socket 1/4 turn CW or CCW. The bulb socket is loose.
The bulb is simply pressed into the socket.
Not sure of the type, but it can be found at your locale auto parts store.
The bulb is used in several places on the 1994 GC, so get apacket with two, if possible.
Assembly in reverse. Be careful not to overtighten the screws as they are replaced

May 08, 2011 | 1994 Jeep Grand Cherokee

1 Answer

Change front turn signal


The side marker light must be removed in order to get at the turn signal light.
There are two screws holding the side marker light which is situated above the turn signal.
Open the hood.
Remove the phillips head screw at the top of the side marker light.
Using a long #2 Phillips screwdriver, remove the screw on the outside of the side marker light. This can be seen by looking between the lower side of the side marker light and the top side of the turn signal.
The side marker can be moved.
The turn signal has one screw on the top of the fixture that must be removed.
Slide out the turn signal fixture. There is a small feature on the lower front corner of the turn signal fixture that you must note to properly reinstall the turn signal.
In order to get to the bulb, rotate the bulb socket 1/4 turn CW or CCW. The bulb socket is loose.
The bulb is simply pressed into the socket.
Not sure of the type, but it can be found at your locale auto parts store.
The bulb is used in several places on the 1994 GC, so get apacket with two, if possible.
Assembly in reverse. Be careful not to overtighten the screws as they are replaced.

Mar 29, 2011 | 1994 Jeep Grand Cherokee

1 Answer

Are front side marker lights suppose to blink


They are NOT supposed to blink only the front facing

Apr 04, 2009 | 1999 Ford Crown Victoria

1 Answer

No turn signals or brake lights


try turning the hazards on and off several times these switches go bad and will keep the lights from coming on

Dec 31, 2008 | 1998 Mercury Grand Marquis

1 Answer

2005 Chevy Tahoe Trailer Running Lights Out


Depending on what type of trailer you have, a blown lightbulb on one marker could kill them all (like the old Christmas light strings). Look at those, and make sure your ground is good.

Nov 26, 2008 | 2002 Saturn VUE

Not finding what you are looking for?
1998 Volkswagen Jetta Logo

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...