Question about 2005 Ford Focus

1 Answer

Have a 1995 ford contour put new front brakes on rotors on the car now abs light came on how do i reset

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,763 Answers

The system will reset itself once the problem is fixxed, there are wheel speed sensors on each wheel, the light was not on before then you must have broken or knock off a connector to the sensor, check the connectors on the sensors and make sure they are pluged in, you will see the wire going behind the rotor area.heres a picture of it, another way is to have the computer scanned for codes, there will be abs codes and the code or codes will tell you what has failed, for example it could say left front speed sensor,if you cant find anything at the sensors then have it scanned for the codes, you will need to have a shop scan it unless you have a scan tool. good day.

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced brakes on 1995 Ford Taurus and now ABS light is on and ABS is disabled


The ABS light only comes on because of a fault. You need the ABS control module scanned for the code that set when the light comes on. There is no RESET

Mar 28, 2014 | 1995 Ford Taurus

1 Answer

I put new brake pads on the front and now i dont have a full pedel of brake.The abs light and traction light are both on


how much brake fluid did you remove or put brake shoes on wrong reason abs light on.check brake fluid.when replace front brakes you have make sure mastercylinder reservoir corver on then pump brake pedal seat brake shoes against rotor then check brake fluid level.

Dec 27, 2012 | 2000 Chrysler Concorde

1 Answer

1995 Ford changed front rotors and everything seems fine, but on stopping the Abs comes on at the last minute. How do you adjust the sensors?


you can not adjust them you can replace them or take them out and file down the rust where the speed sensor sits.

Mar 26, 2012 | 2005 Ford Futura

1 Answer

2006 Ford E350 disk brakes front and rear all new just installed now directly after the abs lite stays on however brakes work fine don't know about abs system though do you think I could have confused the...


Using the C-Clamp is the proper way to retract the pistons. So it wasn`t your fault for the aABS light.
check the brake fluid level, check the wheel speed sensors connection on all 4 wheels,
Drive vehicle for a few miles too see if the ABS resets itself.
If the light is still on, then have the truck checked with a SCANNER for the ABS problem..

Mar 02, 2011 | 2006 Ford Econoline Cutaway

1 Answer

Abs is still on. i have new pads and master cylinder.


The ABS system is separate from the normal braking system (pads, rotors, master cylinder, etc.). It's essentially a computer that pumps the brakes during heavy braking to prevent, or at least reduce the possibility of a skid. The ABS system needs to be tested and repaired by a qualified mechanic.

Bill B

Aug 06, 2010 | 1998 Ford Contour

2 Answers

1998 Ford Contour ABS light and one wheel partially braking


could be but not likely. sound like abs pump or abs ecu failure. to make sure check DTC's

Jun 02, 2009 | 2000 Ford Contour

1 Answer

My brakes are shaking... I own a ford contour 95...


sounds like your rotors need machining this is caused by hot brakes getting water on them or very very hard braking
hope it help rate please

Dec 16, 2008 | 1995 Ford Contour

1 Answer

Wheel bearing ford contour


this comes a a hub assembly
you need to remove the brakes and brake rotor
the center nut holding in your CV shaft
in the hub you will find holes that you can put your socket threw to remove the mounting bolts.
07ae802.jpg

Oct 18, 2008 | 1998 Ford Contour

Not finding what you are looking for?
2005 Ford Focus Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...