Question about Ford Mustang

1 Answer

I drive a 04 mustang v6 and when i push on clutch it makes a loud squeling noise and the clutch gets hard 2 push

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

The pressure plate and release bearing are worn out. You will need a new clutch disc, pressure plate and release bearing. You can either get an estimate from a garage or replace the parts yourself. To replace you will need a transmission jack and mechanics tools.Remove the drive line. Support the engine with a stand and block of wood. Remove the rear bracket. Position the jack under the transmission and loosen the clutch adjustment. Separate the linkages and release bearing fork . Remove the bolts surrounding the bell housing. Carefully back out and lower the transmission. Remove and replace the clutch assembly, and pilot shaft bushing (brass part at the center of the flywheel). You use a wooden dowel or a pilot shaft tool to orient the clutch disc inside the pressure plate while re-installing.

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot depress clutch


may need a new one or ajust--bring it to a specialist or honest mech-not a dealer

Aug 17, 2013 | Ford Mustang Cars & Trucks

1 Answer

Squealing noise on 01 ford ranger while accelerating


Hi, I'm glad to help!

First you need to remove the drive belt and spin the Alternator, A/C Clutch and Water Pump pulley's and see if you hear the squeal. Its possibly it may have to be under a load before you hear it but its worth a try. It's also possible it could have something to o with the Throttle Body or Intake Manifold. Hope this helps and have an awesome day.

Feb 25, 2013 | Ford Ranger Cars & Trucks

1 Answer

91 ford mustang clutch is stiff and makes a loud squealing noise


Sounds like the actual pressure plate but you won't be able to confirm without dismantling it.

Mar 01, 2017 | 1991 Ford Mustang

1 Answer

I have a manual transmission in my '04 Mustang. When I begin to depress the clutch, an odd grinding sound starts, not loud but enough to warrant concern. As I drive, the car sounds fine. Switching gears...


Worn throw out bearing, replace or the problem may damage other components. This requires dropping the entire transmission. this bearing sits between the clutch pressure plate and clutch slave assembly. When the clutch pedal is pressed, the bearing makes contact with the spinning clutch pressure plate. If defective, grinding/squealing noises may be heard. If the bearing fully fails, loose debris may damage other components. Replace immediately!!

Dec 11, 2010 | 2004 Ford Mustang

1 Answer

I have a 1994 Nissan pickup. v6 manual trans. I get a loud hum as I drive. But when I press the clutch in, the hum stops. release clutch and hum starts. Could this be the Clutch fan?


No, By pushing in the clutch to stop the hum all you are stopping from turning is the transmission and ( transfur case if 4 wheel drive ) the engine is still running ..and some parts in the rear differential . I have had 4 nissan pickups and currently drive a 1995 pickup, without actually hearing the noise I would look toward the transmission, these Manual transmissions are very prone to bearing failure. This has happened to 2 of the one's I have had including the one I have now. You can also see as time goes by if the noise is quieter in fourth gear than others because this is direct drive and not as many trans bearings are involved Good Luck

Oct 22, 2010 | 1994 Nissan Pickup

1 Answer

Grinding in the gearbox area while driving


manual ,thank heaven ,dont see many autos here in spain,right without driving car so i can hear it then it stands two possibilities ,when clutch is depressed you hear a noise like a grinding squel ,this is the thrust bearing ,if you hear a rumbling noise that disappears when clutch is depressed then this is lay shaft bearings ,Now also the problem can be the fingers on the clutch plate are worn and the bearing is pushing the clutch plate fingers down but if one or two are worn away then the thrust bearing is being pushed through the pressure plate ,either way a new clutch is need and as these vehicles are rear wheel drive they are not difficult to renew ,Just have to make yourself a clutch alignment tool from a broom handle .Dont be scared of it they are not that difficult to do just dirty and messy thats all the hardest part is aligning the clutch so the spigot shaft goes through easly and you dont have to struggle pushing the gearbox in

Dec 12, 2009 | BMW 325 Cars & Trucks

1 Answer

04 toyota corlla 5 speed


If there is only one click when you go into first or reverse. Then look at the linkage on the clutch pedal. If you push the clutch pedal down and up (without putting it into gear) does it still make the click sound? Is the transmission going into gear normal? Is the throw-out bearing making any noise? A throw-out bearing can make a loud click noise.

Jun 18, 2009 | 2004 Toyota Corolla

1 Answer

Truck makes loud noise unless clutch is pushed in


chances are the adjustment of the throwout bearing fork is the problem . because of vibration that is the rattling that you are hearing. correct adjustment should be as follows.

#1...peddle travle should be no more than 1 1/2 inches

#2...the clearance between throw out bearing and fork no more than 1/2 inch

#3...clearance between fork and fork stops is 1/8 inch

also there should be grease zerts in the shaft that holds the fork and linkage make sure they are not dry of grease...please rate the solution....thanks

Sep 22, 2008 | 1987 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...