Question about Chevrolet C1500

1 Answer

Starter removed by ?? need wire d-gram for new starter--1987 chev v8 pickup

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,002 Answers

Unless they cut the wires you shouldn't need a diagram. There are only two places to put them and both posts are radically different sizes.One takes a 5/16 wrench and the other takes 1/2 or 9/16. Just hook them up by their sizes. The small one goes on the inside terminal of the solenoid. Be careful tightening it because you can twist the end off and that can't be repaired. The rest go on the center post. Be sure to clean all the terminals before you put them on, bare shiny metal. It could save you a lot of grief later on.
If the wires were cut, the one for the inside of the solenoid would be the smallest guage wire, probably purple, but I have seen it other colors. The wires going to the center post will be a heavier guage wire and should all be red or pink.There should be at least 2 and they both will have a black pljug about 8 inches or so back from the starter. These are fusible links. They may be together on 1 terminal end but I have seen them separated. Hope this helps.

Posted on Mar 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need diagram for '87 ford pu seraphine belt


For the 1987 Ford F150:

I do not know if you have the 4.9L In-Line 6-Cylinders, 5.0L V8, or the 5.8L V8 Engine or what Engine Options ( AC/No AC, etc.).

Click on the following free direct Link. It has several Serpentine Belt Diagrams for the 1987 Ford Pickups.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/1987/make/ford/model/pickup/1987_ford_pickup_drive_belt_routing_diagram.htm

Apr 09, 2010 | 1987 Ford F 150

1 Answer

Mini Wini on a 1987 Toyota. New battery. Won't start.


Well if you replaced the starter solenoid it sounds like something as simple as a bad battery connection,I would take both battery cables loose and clean them off with something like some 100-150 grit sandpaper or they make a battery and battery wire connection cleaning tool.

Apr 08, 2010 | 1987 Toyota Pickup

1 Answer

Change starter on 1987 plymouth sundance. Tools needed


a rachet with extension... i think the bolts will be 13 or 14 mm. unhook the battery first. there are two bolts holding the starter on. remove those two bolts and pull the starter. do NOT remove the wires till you have the replacement starter in hand. transfer the wires one at a time from the old starter to the new one. reinstall the starter with the two bolts and hook up the battery when it is done.... should start with no issues.

Dec 11, 2009 | 1987 Plymouth Sundance

1 Answer

How do i change the starter on a 1987 chev blazer


I am assuming your Blazer is an S10 4 wheel drive with a 6 cyl. engine (if i'm wrong...let me know). As you can see by this web link: (copy & paste) http://www.autozone.com/autozone/catalog/parts/partsShelf.jsp?displayName=Starter&currentPage=1&categoryDisplayName=External+Engine&navValue=15300045&itemId=45-0&parentId=53-0

The diagram shows that it is located under the vehicle and held in place by at least two long hex head bolts. Before removing it's a good practice to take off your positive cable at the battery first. Now remove electrical wires at the starter and then unbolt it, or sometimes its easier to get at the electrical wires if you unbolt it first, but be careful...the starter is quite heavy! Make sure to hold it up while unbolting so it won't just fall to the ground and possibly causing damage to the electrical wires still attached! Always better if you can remove the wires first to avoid that from happening. Now reverse the process to install your new one...and last...to put your cable back on the battery. Hope I helped you!

Nov 10, 2009 | 1987 Chevrolet Blazer

1 Answer

How do i remove my starter on a 1987 chevy


Two mounting bolts. Two wire terminals. Disconnect battery first for safety. You may need to remove exhaust manifold or something to get at it. The starter is mounted with flat metal shims that adjust how it meshes with the flywheel. Save those and try various positions with your new starter till it doesn't make too much noise when you start.

Sep 26, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

How do i replace a starter on a 1995 F150 ford pickup. Engine model 5.8L V8 FI, 315 CID


place truck on ramps or jack stands, rfmove battery cables from battery, go under truck locate starter, remove wires connected to starter, remove bolts from starter, it will fall out if not careful

Sep 16, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Now i replace the ignition cylinder but i steel kent starer on my chevrolet 1987 s10 pickup


check power on large yellow wire from ignition swith while turning key to start possition,this is the wire that powers the solenoid to starter.also may try tapping on starter with hammer while someone is trying to start.If starts while performing tap method you will need a starter. If no power to yellow wire at ign switch while starting will need electrical part of ignition.

Jun 16, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

Can you show where the fuel line is for a 1987 chev pickup


runs out of tank and along drivers side frame rail..

Nov 30, 2008 | 1987 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...