Question about 1999 Ford F150 Regular Cab

1 Answer

I WANT TO PUT A 1985 5.8 HO FROM A F250. INTO A 1999 F150 5.4. WILL THIS BE A DIRECT SWAP? MOTOR MOUNTS, TRANNY, ETC. I UNDERSTAND I WILL HAVE TO USE THE 5.4 INTAKE, PULLIES, AND FUEL RAILS ETC.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,066 Answers

Check with an auto parts store to see if both engines/vehicles use the same front end gasket/seal and/or motor mounts. im for real- just have autozone or whoever look up the part numbers for the mounts and fronnt end gasket/seal for both vehicles, and if they match, then it should be a go.

the front end gasket/seal is locaded between the engine and tranny, and if both models/engines use the same gasket/seal, then the trannys will match up perfectly.

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

3500. Can I run this motor w/existing wiring or do I need harness and ECU from older van?


Mark, You will need it all, including fuse and relay centers, tranny wiring too probably, etc,etc.

Feb 22, 2016 | 2001 Chevrolet Express

3 Answers

Motor mounts


I wouldnt recommend swapping motors on different models, even if they appear to fit properly. It will always create some king of complication along the way, even if it appears to run smoothly initially.
I dont think they make cross over mounts for older models. You may have to get one fabricated. But you can try various mechanics in your town, who may have one.

Hope that helps. If you found my answer satisfactory, kindly take a moment to "Accept" my solution.

Thanks in advance,
IrishDruid.

Jun 06, 2008 | 1986 Jeep CJ7

1 Answer

What does it take to put 4.0 in jeep tj, take out 2.5


you will need all new harness and EFI,
move the engine with the FULL EFI system and it can work
the primary wiring will be worse pain, ASD and all that.
mech, (mounts, and tranny)

why not join a jeep forum a real one. and post to the swaps sections
or better , read there swaps sections first.
me, i sell it and get 4L. , save 100hr labor.
here is the parts cat
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see it>, no look up the tranny part numbers, (a/t or m/t?)
or clutch or bell housings.. and mounts, they are all there.

google jeep forum engine swap

here ill do that for you......

https://www.google.com/webhp#q=jeep+forum+engine+swap

bingo?

Jan 27, 2014 | 1995 Jeep Wrangler

1 Answer

My 1985 transmission (manual ) pops out of gear when power is applied


If it is popping out of gear then your synchro-gears are shot and the transmission needs to be rebuilt. I know that sucks to hear but there aren't many things that would cause your tranny to pop out of gear. The only other thing it might be is a broken motor mount and a broken tranny mount. But that's not likely to happen and I think you know if you broke a motor mount and your engine was rising and falling as you accelerate and decelerate.

Check your mounts then start calling your local wrecking yards!

Good luck, I hope this helps you.

Sorry it sounds so bad, but trannys are cheap and fairly easy to replace in your driveway.

Jan 10, 2011 | 1994 Chevrolet S-10 Blazer

1 Answer

I just did a motor swap in a 1997 sunfire. when I


could be a bad motor mount or one that is loose. tranny mount could be bad also id try these two areas first.

Apr 04, 2010 | 1997 Pontiac Sunfire

2 Answers

How to install 350 chevy frame mounts in a 1985 chevy impala


The 1985 Impala came standard with the Chevrolet 305 V8. All Chevrolet small block V8's from 265 cubic inches to 400 cubic inches from 1957 to about 1989 used the same block with almost no difference in the castings, so the motor mounts should fit from one block to the next. If you are trying to swap in a 350 newer than 1989, then the motor mounts are different, and you will have to have them fabricated by a local welder, machine shop, or perhaps the best, a local short-track race car driver/builder. Those guys can build anything.

Feb 16, 2010 | 1985 Chevrolet Impala

1 Answer

1985 Mercedes 190E auto tranny swap - wont go into gear


are you checking tranny fluid level.check condition of fluid if it look brown smells change tranny fluid and filter.fluid change dont help .you got pump and input clutch problems.

Apr 28, 2009 | 1985 Mercedes-Benz 190

3 Answers

Engine swap 1985 240 DG into 1983 Volvo 245


Go ahead and swap the transmissions, and that should be about it. The b230 and b23 engines are basically the same block, so there should be no trouble there.

Apr 07, 2009 | 1984 Volvo 240 Series

5 Answers

Need to change engines


If you have a 22r carbed then all 22r carbed engines from 1981-1995 will interchange. You may need to use sensor out of your old engine however. The 20r,22r,22re,22ret all have the same mounts and tranny bolt patterns. how ever there are lot of differences. you can swap from a 22r to a 22re but you must also swap the entire vehical wiring harness to do it right. if you have a 3.0L i would keep the same engine. some people have swap to the tacoma 3.6L but that is a expensive swap not exsactly bolt on so to say. If you have a 22re then stay with the 1986-1987 22re because the newer 22re use different computers, electronics ,sensors and more.. Same story with the 22ret. I hoped this helped.

Mar 26, 2009 | 1987 Toyota Pickup

1 Answer

Samurai toyota moto swap


You will have to Change the Wiring Harness and all for this Swap. Measure the Width and Length of the Motor Mounts on the Suzuki and the Toyota and see if you will need to Manufacture new Mounts. Check the Tranny Mounts also. Please Rate My Response! Thanks!

Feb 03, 2009 | 1989 Suzuki Samurai

Not finding what you are looking for?
1999 Ford F150 Regular Cab Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...