Question about 1999 Dodge Intrepid

2 Answers

Looking for a picture of the diagram of where the thermostat is located on my 1998 2.7 liter dodge intrepid PLEASE!!!!!

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

After I installed a new thermostat 190 degree and still no heat. my car 2003 dodge intrepid 2.7L V6 Engine

Posted on Aug 24, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 8,152 Answers

Hi, I don't have a picture, but trace the big hose from the bottom of the radiator to the engine, and it will be under the housing where the hose connects.


2.7L Engine

  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
  2. Drain cooling system.
  3. Remove radiator lower hose from thermostat housing.
  4. Remove nuts from heater tube flange studs.
  5. Loosen starter bolt at heater tube bracket.
  6. Pull heater tube out of thermostat housing and position out of the way.
  7. Remove bolt and two studs.
  8. Remove thermostat housing, O-ring and thermostat.
  9. Remove thermostat housing bolts.

To install:
  1. Clean gasket sealing surfaces.
    NOTE Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
  2. Install thermostat and seal into thermostat housing .
  3. If removed, install two studs.
  4. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
  5. Lubricate new heater return tube O-ring with coolant.
  6. Position heater return tube flange over two studs. Install nuts.
  7. Tighten retaining nuts to 53 inch lbs.(6 Nm).
  8. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
  9. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
  10. Refill cooling system.
  11. Inspect for leaks.
  12. Connect negative cable.

Posted on Mar 26, 2011

  • Hung Dung Aug 24, 2013

    my car dodge Intrepid 2003, after I installed a new themostat 190 degree and still no heat???? Please help. Thanks

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the thermostat on an 1999 dodge intrepid


thermostat is located in housing on lower left side of engine near the oil filter and attached to the lower rad hose (on a 3.5 liter anyway)

Mar 07, 2015 | 1999 Dodge Intrepid

1 Answer

Need picture location for 3.2 liter dodge intrepid crank sensor


Look on passenger side at back of engine/transmission housing area.
12_12_2011_1_56_03_am.gif

Dec 11, 2011 | 2001 Dodge Intrepid

1 Answer

I need a diagram that shows me exactly where the thermostat in a 2002 dodge intrepid with a 2.7 engine is/ in otherwords show me what it looks like in the car


on most vehicles you follow the TOP radiator hose to locate the thermostat ,, But on the 2.7 is at the motor at the Lower hose, I'll try and find you a picture or diagram , here is a step by step link that tells you how to replace it, http://www.fixya.com/cars/t1324836-2004_dodge_stratus_2_7_thermostat

Sep 24, 2011 | Dodge Intrepid Cars & Trucks

1 Answer

Can you give me a spark plug wiring diagram for a 1995 Dodge Intrepid?


1995 Dodge Intrepid 3.3 liter V-6 VIN "T"

9c7fa62.gif


1995 Dodge Intrepid 3.5 liter SOHC V-6 VIN "F"

084a3e3.gif


Hope this help (remember comment and rated this).

Apr 08, 2010 | 1995 Dodge Intrepid

2 Answers

CAN NOT LOCATE THE CRANKSHAFT POSITION CENSOR ON MY 1996 INTREPID


It should be on the transmission by the passenger side of car. It has three wires connected to it.
1998 Dodge Intrepid
the crank sensor is on the passenger side of the car on the back of the engine. Check right up there by the transmission housing.
1994 Dodge Intrepid 3.3 liter

Jan 01, 2010 | 1996 Dodge Intrepid

1 Answer

Need Diagram of water pump on a 1998 Dodge Intrepid 2.7,


the water pump is timing chain driven and to replace it requires serious disassembly of the engine. it is a 13 + hour job and is not for the casual mechanic

Apr 13, 2009 | 1998 Dodge Intrepid

2 Answers

Need a 3.5 engine mounting diagram for 97 dodge intrepid and 2.7 engine mounting diagram for 02 dodge intrepid


Google 1997 Dodge 3.5 liter Engine Mounting Diagram. Same for the 2002 engine. I guarrantee you will find it.For some strange reason you would'nt call your local Dodge dealer and ask them where you can go to on the web and locate it.

Jan 06, 2009 | Dodge Intrepid Cars & Trucks

3 Answers

THERMOSTAT PICTUREDIAGRAM OF 1999 DODGE INTREPID, 2.7 ENGINE SIZE


It is located on the left side of the engine down where the lower rad hose meets the engine block. It is fairly difficult to change.

Oct 02, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Intrepid Logo

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...