Question about 1996 Toyota Previa

Open Question

Power steering belt slipping (squeals when in full lock) i have adjusted by the wing nut that i think is in the alternator. do i just losen that adjuster and slip belt of and replace?.....the belt is showing signs of wear so needs replacing

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ronald_kate_
  • 111 Answers

SOURCE: timing belt on 1996 mazda protege slips during startup

Hello, this to me sounds like your fan belt slipping (not timing belt). To adjust the fan belt you need to undo your bolt on the alternator, pull it tight onto the fan belt and while holding it tight do the bolt back up tightly. this will stop yoour fan belt from slipping. I hope this helps.

Posted on Nov 06, 2009

johnthejag
  • 286 Answers

SOURCE: loud squealing from power steering pump - do I need new PS pump?

Hi Norman,

Sounds like the adjustment may not be correct on the power steering belt, with the tension not being enough, after you replaced the belt ?

Try giving it a little more tension, and go from there.

Hope I have been of help.

Good Luck !

John.

Posted on Jan 15, 2009

  • 1 Answer

SOURCE: 1999 buick lesabre occasional trans slip on take off

There is a recall for the transmission that involves your exact problem. Call a dealer and see if your VIN is eligible for the recall. Check the NHTSA website for the exact details.

Posted on Jun 25, 2009

CarMech97
  • 427 Answers

SOURCE: My 97 miata has been having terrible squeaking

The alternator is loading up too much for some reason.
Had the same issue on my friend's 2001 Mazda Protege. Turned out the voltage regulator in the alternator was faulty. Had the alternator rebuilt. A week later, it acted up again! There is apparently another issue, but I have not been able to figure it out.
Unfortunately, I don't have a clear answer for you, but, one's thing's for sure. Mazda has to stop using crappy Ford electrics in their cars.

Posted on Oct 07, 2009

miket756
  • 2702 Answers

SOURCE: leaking oil at spline shaft slip yoke at rear of transmission

there is a long bush type bearing in this tunnel just at the end were the seal fits in it can were out and let the prop shaft flap about, this in turn rips the seal to bits,,,also the yoke has a polished part on the end that go's over the spline into the end of the gear box tunnel the seal can were a groov into this part, and no amount of new seals will stop it leaking them as the new seal runs in this worn out groov, again ripping it to bits,,,test the long bush type bearing by holding the prop shaft yoke and pushing it up and to the side, if it moves about replace the bush in the end of the tunnel as well,, its a push in fit! with a big hammer!!
if the yoke has a groov in it you need a new prop as all prop shafts are balanced so you can just fit a new yoke it could throw the car up in the air when your driving it down the free way,,,,by shaking it apart
i hope this is of help to you

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My belt squeal own my 95 tahoe will it miss with the power steerring


belt squeal is the result of a badly adjusted or failing belt. If it also drives the power steering pump then the problem when it squeals will be from the driver holding it on full lock and not backing of a bit

Dec 28, 2013 | Cars & Trucks

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

How to remove belts from 1994 dodge caravan 2.5 liter


Drive Belts

Print


INSPECTION

See Figures 1, 2, 3, 4 and 5
Check the condition and tension of all drive belts every 12,000 miles, or at least once a year. Loose drive belts can lead to poor engine cooling and diminished alternator, power steering pump, air conditioning compressor, or emission air pump output. A belt that is too tight places a strain on the bearings in the driven component.


0900c15280215ae4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: There are typically 3 types of accessory drive belts found on vehicles today


0900c15280215ae5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: An example of a healthy drive belt


0900c15280215ae6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Deep cracks in this belt will cause flex, building up heat that will eventually lead to belt failure


0900c15280215ae7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: The cover of this belt is worn, exposing the critical reinforcing cords to excessive wear


0900c15280215ae8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Installing too wide a belt can result in serious belt wear and/or breakage
Replace any drive belt that is glazed, worn, cracked, or stretched to the point where correct adjustment tension is impossible. If two belts are used to drive a component, always replace both belts when replacement is necessary. After installing a new belt, run the engine for ten minutes, shut OFF the engine and recheck the belt tension. Readjust if necessary.


ADJUSTMENT

See Figures 6, 7, 8, 9 and 10


0900c15280215ae9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Engine belt tension chart-2.2L engines


0900c15280215aea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Engine belt tension chart-1987-89 2.5L engines


0900c15280215aeb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: Engine belt tension chart-2.6L engines


0900c15280215aec.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: Engine belt tension chart-1990-93 models


0900c15280215aed.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 10: Engine belt tension chart-1994-95 models
Two popular methods of checking drive belt adjustment are; the Belt Tension Gauge Method and the Belt Deflection Method. The former requires a special gauge and the latter requires a straight edge and scale or just a good eye for measurement. The deflection method will be used in the following belt replacement instructions. A rule of thumb for checking belt tension by the deflection method is to determine the midpoint between two pulleys of the drive belt and press down at that point with moderate thumb pressure. The belt should deflect to the measurement indicated in the following installation procedures. Adjustment is necessary if the belt is either too loose or too tight.

WARNING A belt adjustment which is either too loose or too tight will eventually damage the accessory that belt is driving. A too loose adjustment allows free-play in the belt which could transfer a whipping motion or shock to the accessory drive pulley. Similarly, a belt which is too tight will preload the accessory bearings, leading to early failure.


REMOVAL & INSTALLATION

See Figure 11
Raise the front of the vehicle, support on jackstands and remove the lower splash shield if access is hampered due to space limitations when changing drive belts.


0900c15280215aee.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 11: Support the vehicle, then remove the lower right side splash shield for access to the drive belts
2.2L Engines
A/C COMPRESSOR DRIVE BELT
See Figures 12, 13 and 14


0900c15280215aef.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: A/C compressor drive belt adjusting points-2.2L engines


0900c15280215af0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 13: Loosening the locking screws for A/C compressor drive belt removal


0900c15280215af1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 14: Removing the A/C compressor drive belt from under the vehicle

  1. Loosen the idler pulley bracket pivot screw and the locking screw.
  2. Remove the belt and install a replacement.
  3. Using a breaker bar and socket apply torque to the welded nut provided on the mounted bracket to obtain proper tension.
  4. Tighten the locking screw first, followed by pivot screw. Tighten to 40 ft. lbs. (55 Nm).

ALTERNATOR DRIVE BELT (CHRYSLER TYPE)
See Figures 15 and 16


0900c15280215af2.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 15: Alternator belt adjustment-2.2L engine


0900c15280215af3.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 16: Loosening the locking screw for alternator drive belt removal
If removal of the alternator belt is required, the A/C belt must first be removed.

  1. Loosen the pivot nut, locking screw, and the adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust to specification by tightening the adjusting screw.
  4. Tighten the locking screw to 25 ft. lbs. (34 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (41 Nm).

ALTERNATOR DRIVE BELT (BOSCH TYPE)
If removal of the alternator belt is required, the A/C belt must first be removed.
  1. Loosen the pivot nut, locking nut, and adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust to specification by tightening the adjusting screw.
  4. Tighten the locking nut to 25 ft. lbs. (34 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (41 Nm).

POWER STEERING BELT
If removal of the power steering belt is required, the A/C and alternator belts must first be removed.
  1. Loosen the locking screw, and pivot screw.
  2. Remove the belt and install a replacement.
  3. Install a 1 / 2 in. breaker bar into the pump bracket slot, apply pressure with the breaker bar and adjust the belt to specification.
  4. Tighten the locking screw first, then the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

AIR PUMP DRIVE BELT
See Figure 17


0900c15280215af5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 17: Air pump belt adjustment-2.2L engines
When servicing the air pump, use the square holes provided in the pulley to prevent camshaft rotation.

  1. Remove the nuts and bolts retaining the drive pulley cover.
  2. Remove the locking bolt and pivot bolt from the pump bracket, then remove the pump.
  3. Remove the belt and install a replacement.
  4. Position the pump, then install the locking bolt and pivot bolt finger-tight.
  5. Install a 1 / 2 in. breaker bar into the bracket assembly (block the drive pulley to prevent camshaft rotation), and adjust the belt to specification.
  6. Tighten locking bolt and pivot bolt to 25 ft. lbs. (35 Nm).

2.5L Engines
AIR CONDITIONING COMPRESSOR
See Figure 18


0900c15280215af8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 18: Drive belt adjustment points-2.5L engines

  1. Loosen the idler bracket pivot screw and the locking screws to replace, or adjust belt.
  2. Remove the belt and install a replacement.
  3. Adjust the belt to specification by applying torque to weld nut on the idler bracket.
  4. Tighten locking screw first, followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

ALTERNATOR BELT
See Figure 18
If replacement of the alternator belt is required, the A/C drive belt must first be removed.
  1. Loosen the pivot nut, locking nut, and adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust the belt to specification by tightening the adjusting screw.
  4. Tighten the locking nut to 25 ft. lbs. (35 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (40 Nm).

POWER STEERING PUMP
See Figure 18
If replacement of the power steering belt is required, the A/C and alternator belts must first be remove.
  1. Loosen the locking screw and pivot screw to replace, or adjust the belt.
  2. Remove the belt and install a replacement.
  3. Using a 1 / 2 in. breaker bar positioned in adjusting bracket slot, adjust the belt to specification.
  4. Tighten the locking screw followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

2.6L Engines
ALTERNATOR/AIR CONDITIONING COMPRESSOR BELT
See Figure 19


0900c15280215af9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 19: Drive belt adjustment points-2.6L engines

  1. Loosen the locking screw, jam nut, and pivot nut.
  2. Loosen the adjusting screw.
  3. Remove the belt and install a replacement.
  4. Adjust the belt to specification by tightening the adjusting screw.
  5. Tighten the locking screw followed by the pivot nut. Tighten to 16 ft. lbs. (22 Nm).
  6. Tighten the jam nut to 21 ft. lbs. (28 Nm).

POWER STEERING PUMP BELT
See Figure 19
If replacement of the power steering belt is required, the alternator and A/C belt must first be remove.
  1. Loosen the pivot screw, and the locking screw.
  2. Remove the timing pickup.
  3. Remove the belt and install a replacement.
  4. Install a 1 / 2 in. breaker bar in the adjusting bracket slot, torque to specification.
  5. Tighten the locking screw, followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).
  6. Install the timing pick-up, and tighten to 160 inch lbs. (18 Nm).

Jul 26, 2012 | 1994 Dodge Grand Caravan

1 Answer

Need belt routing diagram for 2001 chrysler sebring lxi


Thanks for using FixYa.




jturcotte_2444.gif

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze



jturcotte_2445.gif

Fig. Accessory drive belt routing-Chrysler 2.7L engine





2.7L Engine
A/C & Alternator Belt

  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Loosen tensioner locking bolt and pivot bolt.
  4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:
  1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
  2. Adjust drive belt tension.
  3. Install the belt splash shield and right front wheel.
  4. Lower vehicle.
    jturcotte_2446.gif

    Fig. Installing A/C & alternator belt-2.7L engine


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and belt splash shield.
  4. Loosen the tensioner locking bolt and pivot bolt.
  5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:
  1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
  2. Adjust the drive belt tension.
  3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
  4. Lower the vehicle.

Power Steering Belt
  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Remove the air conditioning compressor/alternator belt.
  4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
  5. Remove the power steering belt.

To install:
  1. Install the power steering belt on pulleys.
  2. Adjust drive belt tension.
  3. Install the air conditioning compressor/alternator belt.
  4. Install the belt splash shield and right front wheel.
  5. Lower vehicle.


Oct 27, 2011 | Cars & Trucks

2 Answers

My lexus sc 300 makes a squealing sound when I start it, and when I turn the wheels sharply to the right and left (while it is parked and running. My power steering pump supposedly has to be replaced,...


Hi Genebaran, I doubt very much if the steering pump needs replacement, but the drive serpentine belt does. The squealing happens because the belt is slipping on the pump pulley when the pump is under load when the steering is turned to full lock. By the way, don't keep the steering wheel at full lock for longer than a few seconds at a time, as it will place the pump under too much load! Tell your mechanic to fit a new belt. Advise the mechanic to make a sketch of the routing of the belt before he removes the old one. Regards Johngee10

Jul 22, 2011 | 1992 Lexus Sc 300

1 Answer

I own a 2003 Mitsubishi Galant 2.4L ES. When i turn my car on the Auxiliary belt makes a squealing noise for a bit then it stops. But it doesnt always make this noise, and it has something to do with...


hi there, here is what i have found for you, i hope it helps:
  • Look at where the drive belts are located on your Mitsubishi Galant. Depending on models, you may need to jack up the vehicle to access the bolts for the belts.

  • Find the bolt assembly for the belt. This bolt structure will be on or near the main component that the belt serves. Look at all of the pulleys around which the belt winds, and you will find a bolt system to adjust tension. For an alternator belt, the bolt system is by the alternator. For a power steering belt, look near the power steering pump.
  • Find the lock nut that holds the long adjustment bolt in place and use your wrench to loosen it. This is the bolt the loosens the belt tension so that you can remove it.
  • Turn the adjustment bolt. Turning the adjustment bolt moves the component either toward the engine in order to loosen belt tension, or away from the engine in order to tighten belt tension.
  • Slip off the old belt and install the new one, once the belt tension is released. Make sure the belt is correctly seated on all pulleys.
  • Turn the adjustment bolt the other way to bring the component away from the engine and add belt tension. Test the belt for correct tension by pressing on it and checking deflection.
  • Tighten the adjustment lock bolt and the pivot bolt, when the belt has the right tension.
  • cheers

    iain

    Apr 27, 2011 | 2003 Mitsubishi Galant

    1 Answer

    Replaced pressure line on power steering. now battery light comes on. belt squeeled when started, then stopped. Did power steering fluid get on belt and caused it to squeal and slip?


    If you have a 4cyl then the belts for PS and alternator are separate. Taking a peek under the hood when the engine is running should give you a better idea if a belt is slipping, broken, etc. A common source of squealing is an alternator belt that is too loose and slips under heavy load charging the battery after startup. It's possible that some sort of problem happened due to replacing alternator belt but that belt slipping should be pretty easy to see. (again ... speaking of the 4cyl / 22RE enging)

    Oct 08, 2010 | 1994 Toyota Pickup

    1 Answer

    How do you change the belt


    BELT ADJUSTMENT
    MANUAL BELT TENSIONER
    Loosen rear mounting bolts of idler pulley or power steering pump (if equipped). Loosen power steering pivot
    bolt and lock nut (if equipped). Turn adjusting bolt to tighten belt to specification. See BELT ADJUSTMENT
    SPECIFICATIONS
    table. Tighten bolts and lock nut to 20 ft. lbs. (27 N.m). For serpentine belt routing, see
    For the routing just draw a picture befor romoving the belt. There are 4 different routings and I don't have enough info for yours. Without the proper tool the adjustment spec won't do you any good so before you take off the old belt get a feel of how thight it is and try to match the new one. best thing to do it make it loose enough so it squals when turning the steering
    wheel to the extream or stop then tighten the belt little at a time till it doesn't squeal then just go a little bit more. If the belt is too tight it will wear out bearings in water pump,Alt, pullys ect. If its too losse it will squeal and wear out the belt so take your time on the adjustment.

    Jun 25, 2010 | 1998 Jeep Wrangler

    1 Answer

    Replace serpentine belt for 6 cylinder 4wd


    Loosen the power steering pump rear mounting bolts, pivot bolt and lock nut and then loosen the power steering pump adjusting bolt. Slip the belt on and tighten the adjusting bolt until you can push the belt in about one inch midway between the A/C and alternator pulleys. Then tighten the lock nut, pivot bolt and mounting bolts and that's it.

    It helps to diagrams to go with the instructions. Get yourself factory service manual, promanuals.net has them for around 20$ or so.

    Sep 23, 2009 | Jeep Cherokee Cars & Trucks

    Not finding what you are looking for?
    1996 Toyota Previa Logo

    Related Topics:

    450 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...