Question about 2004 Mazda 3

1 Answer

Mazda 3 2004 Oxygen Sensor

Hi. I want to know what type of oxygen sensor does the Mazda 3 2004 2.3L has (4-wire, 3-wire, etc). Part number is LF66-18-861B. Thanks in advance. Mauricio

Posted by on

  • OMARTELLEZ08 Oct 14, 2008

    I HAVE A MAZDA MVP VAN 2001 I NEED THE TEMP. SENSOR AND THE 4 GEAR SENSOR

    PART #P0128 AND # P0734 IF ANY BODY KNOW WERE I CAN GET THEM

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 183 Answers

It calls for a four wire sensor. Try wwwoxygengeek.com call there 1800 number for a thorough listing.Because somtimes they dont list a vehicle on there site.Good Luck!!!

Posted on Aug 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many 02 sensor and how many wire each sensor


depending on the engine make
v8 and v6 have 2 oxygen sensors( O2S) , one after each cat converter with 2 wires and 2 heated oxygen sensors ( HO2S) in the exhaust manifold/ pipe before the cat converter with 4 wires each
6 cyl and 4 cyl engines have one oxygen sensor after that cat converter and one heated oxygen sensor before the cat converter

Mar 24, 2016 | Cars & Trucks

Tip

Which Oxygen Sensor Is It?


There are many inquiries online about which oxygen sensor to change. Oxygen sensor failure codes are very common on a lot of vehicles. With all of today's vehicles having at least two oxygen sensors and many having three or four of them, it can be a little confusing as to which one is causing the problem.

Before we get into which sensor is which, we need to have a little discussion about oxygen sensor fault codes. There are several different types of oxygen sensor fault codes. Here are just some of the most common ones:

P0135 "Oxygen Sensor Heater Circuit Bank1 Sensor 1"
P0141 "Oxygen Sensor Heater Circuit Bank 1 Sensor 2"
P0147 "Oxygen Sensor Circuit Bank 1 Sensor 3"
P0152 "Oxygen Sensor Voltage High Bank 2 Sensor 1"
P0159 "Oxygen Sensor Slow Response Bank 2 Sensor 2"
P0171 "Oxygen Sensor Lean Sensor 1 Bank 1"
P0172 "Oxygen Sensor Lean Sensor 1 Bank 2"
P0174 "Oxygen Sensor Rich Sensor 1 Bank 1"
P0175 "Oxygen Sensor Rich Sensor 1 Bank 2"

There are many more possible oxygen sensor codes, but I only listed these to make my point. Many times the oxygen sensor code is NOT caused by the oxygen sensor itself. "Lean" or "Rich" oxygen sensor codes (i.e. P0171, P0174) are usually caused by something other than the oxygen sensor. Something is wrong, causing the engine to run lean (not enough fuel or too much air) or causing the engine to run rich (too much fuel or not enough air). In these cases, replacing the oxygen sensor will not fix a thing. (That is, unless you are trying to fix your bank account from having too high of a balance!) The new oxygen sensor will just set the same code as the original one. This is because the oxygen sensor is not CAUSING the problem, it is only REPORTING the problem.

High voltage codes (like P0152 above) can be caused by the oxygen sensor wires being shorted to another wire inside the wiring harness. Sometimes these codes are caused by bad grounds where some other component is trying to ground through the oxygen sensor circuit. Again, replacing the oxygen sensor will not fix this! In short, the problem needs to be diagnosed before running out and buying an oxygen sensor.

Just because a fault code has "Oxygen Sensor" or "O2 Sensor" or "O2S" in its description does not necessarily mean that an oxygen sensor needs to be replaced. Many do-it-yourselfers believe that all there is to fixing the car is to hook it to the "magic box", collect the fault codes and replace the parts the computer tells you to replace. There is nothing further from the truth.

Fault codes only point you toward which SYSTEM is failing. The system must be diagnosed to find the CAUSE of the failure. If this is not done properly, it will only result in wasting a bunch of your money. This is what you were trying to avoid by doing it yourself!

So, after reading all of the above, if you think you still want to replace an oxygen sensor, but don't know which one; here is how to figure it out:

Oxygen sensors are always numbered like this:

Bank 1 Sensor 1
Bank 2 Sensor 1
Bank 1 Sensor 2
Bank 2 Sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:

Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder #1 is located and, of course, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only one bank and it is always referred to as Bank 1. The exception to the 4 cylinder rule is on certain 4 cylinder engines (specifically, some Toyotas) there are two catalytic converters used. In this case, Bank 1 sensors will still be in the pipe for the catalyst that is connected to cylinder #1 and Bank 2 sensors will be in the other one.

Sensor 1 is always the "upstream" sensor (the one located BEFORE the catalytic converter).
Sensor 2 is always the "downstream" sensor (the one that is located AFTER the catalytic converter).
Sensor 3 refers to the ONLY "downstream" sensor where there are two sensors before the catalyst and only one after the catalyst. On very few vehicles the reference to this reads "Bank 1 Sensor 3".

If you do not know where cylinder #1 is, then you need to get a diagram of the firing order for your engine. Just post a question on FixYa.com and make sure you give the YEAR, MAKE, MODEL, and ENGINE SIZE of your vehicle and one or more of our experts will be happy to tell you how to find cylinder #1.

- DTTECH
ASE Certified Master Automobile Technician


Also check out this article by dttech: What Else Could Be Wrong?

on Apr 29, 2011 | Ford F-150 Cars & Trucks

1 Answer

P0421 code


"FWIW, according to the Mazda factory service manual, the P0421 code indicates "Warm up catalyst system efficiency below threshold".

The DETECTION CONDITION for this code indicates "Number of heated oxygen sensor (rear) inversion becomes closer to that of heated oxygen sensor (front)".

POSSIBLE CAUSES are:

Warm up three way catalytic converter deterioration
Leakage exhaust system
Heated oxygen sensor (front) malfunction
Heated oxygen sensor (rear) malfunction
Mass air flow sensor malfunction
Throttle position sensor malfunction
Vehicle speed sensor malfunction"
I copied the above from a discussion group on the PO421 code. The code can be caused by any of the above listed problems. The vehicle should be further inspected and diagnosed, so you do not have components replaced that do not need to be replaced.

Apr 16, 2014 | 1998 Mazda 626

1 Answer

How many o2 sensors are on a 1999 Silverado 5.3


The 1999 5.3 V8 engine had 4 oxygen sensors. There are two catalytic converters on this engine, one on the driver side of the engine, and one on the passenger side of the engine. This is important to know, as the number of oxygen sensors is directly related to the number of catalytic converters on the vehicle. Driver side is referred to as Bank 1, passenger side is referred to as Bank 2. This is very important to know when looking up replacement oxygen sensors. There is one oxygen sensor in front of, or before the catalytic converter, usually referred to as a pre-catalyst O2 sensor. There is also one behind, or after the catalytic converter, usually referred to as a post-catalyst oxygen sensor. So, you have two oxygen sensors on Bank 1, and two oxygen sensors on Bank 2, for a grand total of 4 oxygen sensors.

Oct 03, 2013 | 1999 BMW 318 ti

2 Answers

P0037. heater sen. where is it on the engine?


The code is for the heater in the O2 sensor bank one sensor two. That would be the sensor after the catalytic converter on bank one.
It could be the sensor itself or the power supply for the heater.

Aug 25, 2012 | 2006 Mazda MPV

1 Answer

Oxygen sensor failure


just buy a universal one its cheaper

Jul 13, 2010 | 2005 Mazda 6

1 Answer

I need a diagram of the exhaust system on a Mazda 626


0996b43f80203328.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2000 MPV

1 PCM 2 Mass air flow (MAF)/intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Fuel tank pressure sensor 5 Engine coolant temperature (ECT) sensor 6 Crankshaft position (CKP) sensor 7 Camshaft position (CMP) sensor 8 Knock sensor 9 Heated oxygen sensor (HO2S) (front, LH) 10 Heated oxygen sensor (HO2S) (front, RH) 11 Heated oxygen sensor (HO2S) (rear, LH) 12 Heated oxygen sensor (HO2S) (rear, RH) 13 EGR boost sensor 14 Power steering pressure (PSP) switch 15 Main relay


0996b43f8020330c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2001 MPV

1 PCM 2 Mass air flow (MAF)/Intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Engine coolant temperature (ECT) sensor 5 Crankshaft position (CKP) sensor 6 Camshaft position (CMP) sensor 7 Knock sensor 8 Heated oxygen sensor (HO2S) (front, LH) 9 Heated oxygen sensor (HO2S) (front, RH) 10 Heated oxygen sensor (HO2S) (rear, LH)* 11 Heated oxygen sensor (HO2S) (rear, RH)* 12 EGR boost sensor


0996b43f8020330f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart- 2002-06 MPV

May 22, 2010 | 2004 Mazda MPV

1 Answer

Where Are The sensor Banks On The 2004 GC


Grand Cherokee oxygen sensor locations for 4.0 and 4.7 engines

510d5d9.jpg


f8b5293.jpg


Four wires (circuits) are used on each O2 sensor:

  • 12–volt feed circuit for the sensor heating element
  • Ground circuit for the heater element
  • Low-noise sensor return circuit to the PCM
  • Input circuit from the sensor back to the PCM to detect sensor operation

O2S Sensor removal Never apply any type of grease to the oxygen sensor electrical connector, or attempt any soldering of the sensor wiring harness.
WARNING: THE EXHAUST MANIFOLD, EXHAUST PIPES AND CATALYTIC CONVERTER(S) BECOME VERY HOT DURING ENGINE OPERATION. ALLOW ENGINE TO COOL BEFORE REMOVING OXYGEN SENSOR.
1. Raise and support vehicle.
2. Disconnect O2S pigtail harness from main wiring harness.
3. If equipped, disconnect sensor wire harness mounting clips from engine or body.
CAUTION: When disconnecting sensor electrical connector, do not pull directly on wire going into sensor.
4. Remove O2S sensor with an oxygen sensor removal and installation tool.

02S Sensor installation
Threads of new oxygen sensors are factory coated with anti-seize compound to aid in removal. DO NOT add any additional anti-seize compound to threads of a new oxygen sensor.
1. Install O2S sensor. Tighten to 22 ft. lbs. (30 N·m) torque.
2. Connect O2S sensor wire connector to main wiring harness.
3. If equipped, connect sensor wire harness mounting clips to engine or body. When Equipped: The O2S pigtail harness must be clipped and/or bolted back to their original positions on engine or body to prevent mechanical damage to wiring.


Hope thats help (remember comment and rated this).

Apr 29, 2010 | 2004 Jeep Grand Cherokee

2 Answers

Where is the O2 sensor located on the 2003 V6 All Wheel Santa Fe and how dificult is it to replace?


Hyundai Santa Fe 2001-05
Heated Oxygen Sensor (H02S): The sensors are located in the exhaust system. On some vehicles, one sensor is located up at the exhaust manifold(s) and the other sensor is located down at the catalytic converter. On other vehicles, both sensors are located down at the catalytic converter.

d2217fa.jpg

How to Replace an Oxygen Sensor
Parts:
1. Oxygen Sensor
2. Oxygen Sensor

Tools:
1. 3/8 in. Drive Ratchet
2. Multimeter
3. Oxygen Sensor Socket
4. Combination Wrench Set
5. Crimp Tool
6. Socket Set
7. Scan Tool

Steps:
Step 1 * Park the vehicle on a level surface. Set the parking brake and open the hood.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.

Step 2 * With the engine off and cool, locate the defective oxygen sensor in the exhaust manifold or pipe. If necessary, lift the front of the vehicle and support it with jack stands.
o Tip: Most vehicles have multiple oxygen sensors. How many sensors, depends on the model year and type of engine.

Step 3 * Disconnect the wire connector at the defective oxygen sensor.

Step 4 * Remove the oxygen sensor from the exhaust system.

Step 5 * If you are installing a universal oxygen sensor, cut off the connector from the original sensor and splice the connector wires to the new oxygen sensor. Follow the manufacturer’s instructions supplied with the sensor.

Step 6 * For threaded oxygen sensors, apply anti-seize compound to the threads and install the new sensor.

Step 7 * For flange mounted oxygen sensors, install a new gasket and tighten the mounting bolts.

Step 8 * Reattach the wire connector from the sensor.

Step 9 * If necessary, connect the OBD I/II scanner and erase the fault code.

Hope help with this (remember rated and commented this help) Good luck.

Mar 01, 2010 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
2004 Mazda 3 Logo

Related Topics:

831 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...