Question about 2006 Ford Fusion

Open Question

2006 ford fusion air bag module location and do you need a tool to get the driver side bag off

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mike258
  • 1498 Answers

SOURCE: Air Bag Replacement 1993 Alero GL

Hi there JM,

I hope everyone is ok.

I worked at a wrecking yard where I pulled hundreds of airbags. I want you to understand, they can be dangerous if handled improperly. You need to take precautions.

Some warnings before you begin. Take these Seriously!!!

  • Alway wear safety glasses.
  • Control the environment - no kids, pets, people horsing around.
  • Disconnect the negative battery terminal. After you are done, make sure no one is inside the vehicle when you reconnect the battery. If your vehicle has an anti-theft system, you'll need to get your activation codes to reset your sound system.
  • Do not use solvents to clean your airbags. They may ignite if accidentally deployed. Use only a damp cloth.
  • Airbags are sensitive to heat in excess of 190 degrees F. Store them accordingly.
  • Airbags are sensitive to impact - handle them carefully
  • Airbags are sensitive to static electricity - ground yourself, Spray the seat and rug with fabric softener (anti-static - ever heard the term 'static cling')
  • Be safe
The procedures are pretty simple

Drivers Side:
  • Disconnect the negative battery cable.
  • Locate and pull the Airbag fuse.
  • Take a ten minute break (allows the firing charge to dissipate)
  • Loosen and remove the retaining screws from behind the steering wheel. Rotate the wheel as needed to access the screws. You may need to purchase new retaining screws in advance to install the new bag.
  • Return the wheel to the straight ahead position.
  • Lift the airbag assembly out and disconnect the wiring connector from the rear of the unit.
  • Inspect the clockspring for damage. If it looks broken, bent or pinched, replace it. If there are hidden defects, the diagnostic module will detect them. If you are in doubt, replace it.
  • Unwrap the new airbag (carefully).
  • Connect the the wiring connector and seat the airbag into the steering wheel. Be sure the wire doesn't get pinched.
  • Install the new retaining screws and tighten them securely.
Passenger side:
  • Loosen and remove the passenger side dash retaining screws
  • Move it downward to release the retaining clips and remove.
  • Unscrew the airbag retaining screws along the edge of the airbag.
  • Move the airbag assembly downward the release it fom its mounting pegs.
  • Remove the airbag from the dash, disconnecting the wire as soon as you are able. I believe your model has mounting guides, if so save them.
  • If there were guides, place them back into the mounting frame.
  • Position the airbag over the mounting frame and reconnect the wiring connector.
  • Mount the new airbag, securely tighten the retaining screws.
  • Remount the dash and screw it back in.
  • Put the fuse back in.
  • Make sure nobody is in the car
  • Reconnect the battery.
All done

One more time, be serious, be careful, be safe.

I hope this helps
Mike

Posted on Nov 26, 2008

  • 399 Answers

SOURCE: replacing drivers side air bag on 2006 pontiac g6

irst, You must get the steering wheel with controls. I believe part numbers were listed above, but bottom line, make sure you get the right color if you are ordering. The black one is called ebony. Prices vary depending on where you get them. I got mine from a salvage yard brand new for $75. Second, You must replace the clockspring with the column harness. If you have a light duty pickup, you will need part number 26101829. This is for a 2 stage air bag. If you have a heavy duty, order part number 26101828. This is for a single stage air bag. If you are unsure, take off your airbag and look to see if it has 1 or 2 pigtails connected to it. 1 is a single stage, 2 is a 2 stage. GM has reduced the number of part numbers available to simplify things. Therefore, you will get a harness equipped with an additional 8 pin connector. This is for the steering wheel speed sensor for quadrasteer. If you do not have quadrasteer, just tape it to the column and don't worry about it. 

Be careful when installing the harness, there are about 14 connectors, I spent 2 hours installing the harness and wheel. 

Posted on Dec 06, 2008

  • 56 Answers

SOURCE: malibu air bag module location

The module is under the passenger side seat,under the carpet.You will have to remove the seat to access it easier.Lift up the carpet and it will be mounted to the floor.

Posted on Mar 03, 2009

kallumin
  • 1 Answer

SOURCE: 97 ford taurus air bag module location

It"s in the steering column...

Posted on Apr 01, 2009

tneubauer
  • 437 Answers

SOURCE: Bad evap sensor

This is sandwiched under the dash and requires dash removal to remove and replace.

Posted on Jun 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 fusion reset air bag light in cluster


Light on idicates a problem with the air bag system , there is a DTC - diagnostic trouble code stored in SRS control module . To reset the light , code has to be diagnosed and fixed for the light to go out . If you don't know that your best bet would be to take it to a qualified repair shop . Special tools are needed to diagnose and repair SRS systems . People not knowing what they were doing have been killed .

Dec 29, 2016 | Cars & Trucks

1 Answer

The drivers side airbag light comes and stays on my 2006 Toyota Rav4 until the car is warm. What's wrong?


you need to get in touch with toyota they had a recall on your vehicle due to airbag.THE STEERING COLUMN ASSEMBLY CONTAINS ELECTRICAL CONNECTIONS TO THE DRIVER'S AIRBAG MODULE HOUSED IN A SPIRAL CABLE ASSEMBLY, WHICH INCLUDES A FLEXIBLE FLAT CABLE (FFC). DUE TO THE SHAPE AND LOCATION OF THE FFC'S RETAINER, THE FFC COULD BECOME DAMAGED WHEN THE STEERING WHEEL IS TURNED.
Consequence: IF THE FFC IS DAMAGED, CONNECTIVITY TO THE DRIVER'S AIR BAG MODULE COULD BE LOST AND THE AIR BAG DEACTIVATED. THE FAILURE OF THE DRIVER'S AIR BAG TO DEPLOY IN THE EVENT OF A CRASH THAT TYPICALLY NECESSITATES DEPLOYMENT INCREASES THE RISK OF INJURY TO THE DRIVER.

Mar 31, 2016 | 2006 Toyota RAV4

1 Answer

Steering wheel airbag removal on 2006 Cadillac cts cant find bolts


There are no bolts ! it takes a special tool , there are spring loaded Fasteners .
Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
Steering Wheel Inflatable Restraint Module Replacement
Tools Required J 44298 Driver Air Bag Removal Tool
Removal Procedure
Caution: Refer to
SIR Inflator Module Handling and Storage Caution in the Preface section.
Caution: Refer to SIR Caution in the Preface section.

showgif.do?image=640349

tif.gif
Caution: A deployed dual stage inflator module will look the same whether one or both stages were used. Always assume a deployed dual stage inflator module has an active stage 2. Improper handling or servicing can activate the inflator module and cause personal injury.
  1. Disable the SIR system. Refer to SIR Disabling and Enabling .
  2. On the back side of the steering wheel are 3 openings for removing the steering wheel module.
  3. Adjust and install J 44298 into 1 of the holes.
  4. Important: Seat the air bag removal tool all the way in to perform properly.
  5. Pull the handle of the air bag tool away from the instrument panel (I/P) releasing one of the spring loaded fasteners.
  6. Repeat this step for the other 2 fasteners.
  7. Pull the inflatable restraint module gently away from the steering wheel.
    showgif.do?image=818476
  8. tif.gif
  9. Important: Note the wire routing positions on the steering wheel module connectors, the redundant control routing positions, and the horn wire routing positions for the correct assembly.
  10. Remove the connector position assurance (CPA) (4) and the electrical connector from the steering wheel module.
  11. Remove the horn contact lead (2) from the steering column cam tower.
  12. Remove the steering wheel module (5

Mar 09, 2015 | 2006 Cadillac CTS

2 Answers

How can I reprogram bcm on 2006 ford fusion


You need a factory scan tool , it only costs about $3,000 ! Does the back lighting work every where else , Instrument cluster , switch on steering wheel, door switch's etc.. If so you have another problem , because all the back lighting is controlled by the SJB - smart junction box , that's what ford calls there body control module !

Feb 26, 2015 | 2006 Ford Fusion

2 Answers

What is 2002 Ford Focus airbag code 23, what should I check?


23 Memory Clear Circuit Improperly Grounded.

Feb 11, 2015 | 2002 Ford Focus

1 Answer

2006 fusion sedan no side curtins or air bags ,does it still have left and right sensers or just a front senser?


Have a dealer run your VIN #

You can learn all about what your car has
off the assy line

Jul 28, 2014 | Ford Fusion Cars & Trucks

1 Answer

My ex husband was in a roll over car accident in his 2006 ford fusion going 70 mph and his air bags didnt deploy. is there a recall on those or does he have a possible case for his injuries?


Front air bags are not designed to deploy in side impact, rear impact or rollover crashes.There are several reasons why your air bag may not have deployed during a crash. The first reason is that perhaps your crash is not the type of accident where air bag deployment would be helpful. For frontal air bags, this includes many, but not all, side impacts, rear impacts and rollovers. This category also includes minor accidents in which the driver and front passenger (if there was one) did not suffer any significant injuries requiring medical treatment. Many people do not realize there are a lot of side air bags that do not deploy during a rollover accident, even when the vehicle rolls onto its side. That is because those side air bags do not include an appropriate crash sensor that can detect rollover crashes.

Aug 03, 2011 | 2006 Ford Fusion

1 Answer

B2293 air bag


That might be a bad Drivers Side air bag Module you need to take into a Ford Approved Dealer , might be still under warranty

Sep 09, 2010 | 2006 Ford Escape

1 Answer

I've been in a wreck the damage is fixed. I have a new airbag control module. I've been told I need to replace the "crash sensors" before installing the new airbag control module. Where are the Crash...


The crash sensors are located inside the computer the accelarometer would of been replaced if the computer was replaced. Or the air bag control modual. The clock spring would need to be replaced but the front magnetic sensors should be fine, they don't normally wear out. they can be damaged but the air bag warning light would flash if it was bad. And the air bag would still not go off unless the other condtions are met to make the bag deploy. The air control modual would have been replaced if it was done by a shop that is part of the service when the bags deploy. The crash sensors are a magnet with a steel ball and when the right speed is reached and the ball is let go from the metal o ring that it sits in it will deploy the first trigger the next trigger would be the acelorometer in the air control module and the impact would have to be strong enought to knock that ball loose as well to trigger the air bag.

Mar 16, 2010 | 2006 Ford Fusion

2 Answers

What is airbag light code 31 and 51 on a 1994 ford taurus


I was unable to locate code 31 in my book here is a copy of the codes. looks like you just need a fuse for #51. this may fix 31 as well.

Diagnostic Trouble Code Table 1994

AIR BAG DIAGNOSTIC MONITOR DIAGNOSTIC TROUBLE CODE PRIORITY TABLE
Priority Code Component/Fault Description
Highest - No Air Bag Indicator - Inoperative Lamp Circuit or No Ignition
Voltage to Air Bag Diagnostic Monitor

Continuous Air Bag Indicator - Air Bag Diagnostic Monitor
Disconnected or Inoperative
12 Low Battery Voltage
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Safing Sensor Not Mounted to Vehicle Properly
22 Safing Sensor Output Shorted to Battery Voltage
23 Safing Sensor Circuit Input Feed/Return Circuit Open
24 Safing Sensor Output Feed/Return Circuit Open
32 Driver Side Air Bag Module High Resistance or Open
33 Passenger Side Air Bag Module High Resistance or Open
34 Driver Side Air Bag Module Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Module Low Resistance or Shorted
42 Center Radiator Primary Crash Sensor Feed/Return Open
44 Center Cowl Primary Crash Sensor Not Mounted to Vehicle Properly
45 Center Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
51 Diagnostic Monitor Internal Thermal Fuse - Fuse Blown Due to
Intermittent Short to Ground
52 Backup Power Supply - Voltage Boost Fault
53 Primary Crash Sensor Circuits - Resistance to Ground or Air Bag
Diagnostic Monitor Failure

Lowest - Rapid Continuous Flashing of Air Bag Indicator (No DTC) All Primary

Sep 30, 2009 | 1994 Ford Taurus

Not finding what you are looking for?

Open Questions:

See all 2006 Ford Fusion Questions

2006 Ford Fusion Logo

Related Topics:

1,091 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...