Question about 2002 Pontiac Aztek

1 Answer

2002 pontiac aztek front wheel bearing hub torque

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 72 Answers

  • Tighten the wheel speed sensor bracket nut to 12 Nm (106 inch lbs.).

  • Tighten ball joint nut to 60 Nm (44 ft. lbs.).
  • Posted on Mar 26, 2011

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Replace front hub assembly 2002 Suzuki XL7


    the front wheel bearing hub?
    XL-7 (the dash matters)
    my wild guess, is the questions was
    what are all steps to do this job. and tools.
    that?
    RTM?

    https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

    http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
    the link shows all years, and variances.

    here is a photo review, that is accurate up to
    1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
    and NON-serviceable.
    http://www.fixkick.com/hubs/FW_BEARINGS.html


    the photo 6a and B
    shows removing the hub,
    so do that , buy a new hub and put it back
    the same way, using the tool stated
    at the stated ranges of torque
    123-180 ft/lbs.
    this range allows you to get the screws into the locking rings.

    Dec 11, 2016 | 2002 Suzuki XL-7

    1 Answer

    2007 Pontiac wave torque settings for wheel bearing replacement


    If it is the drive axle hub nut you are reffering to, the torque spec is 221 ft lbs

    Feb 20, 2016 | Pontiac Cars & Trucks

    1 Answer

    Front wheel bearing torque


    Better late than never Brucy....CLICK HERE TO SEE YOUR WHEEL BEARING GUIDE. Repair Guides Front Suspension Wheel Bearings AutoZone com

    Apr 02, 2014 | 2006 Pontiac Grand Prix

    1 Answer

    Where is the abs plug on pontiac aztek


    The sensors are made right into thee heel bearing hub assembly on this. The plug on the rear is right on the bearing assembly. The front you just follow the wire coming off of the hub. If you do have to replace this hub due to a sensor, don't get a cheap one to fix it. Those go out within about a year and then you just have a wheel bearing problem which is more dangerous than an abs issue.

    Mar 08, 2013 | 2004 Pontiac Aztek

    1 Answer

    TORQUE SETTING ON FRONT WHEEL BEARING NUT ON 2006 PONTIAC TORRENT


    Hello, here is the torque spec for front hub bearing
    Strut to Steering Knuckle Bolt and Nut
    180 N·m
    133 lb ft
    Tie Rod Retention Nut
    50 N·m
    37 lb ft
    Wheel Bearing/Hub Mounting Bolt
    130 N·m
    96 lb ft
    Wheel Drive Shaft Spindle Nut
    205 N·m
    157 lb ft

    Nov 07, 2010 | 2006 Pontiac Torrent

    1 Answer

    Rear Wheel Bearing Repair; 2005 pontiac aztek


    Remove the brake caliper
    Remove the disc, (rotor)
    Remove the 34mm nut on the axel shaft
    Remove the three (3) bolts from the back side
    You will need a wheel puller (three jaw will work well)
    Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
    Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

    May 01, 2009 | 2005 Pontiac Aztek

    2 Answers

    2003 Pontiac Montana Front Wheel Bearings


    Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

    Apr 08, 2009 | 2003 Pontiac Montana

    2 Answers

    Road noise from right front wheel, louder at higher speeds, worse when turning left


    front right wheel bearing will cost you 80$ might want to check the left side bearing too.

    Jul 30, 2008 | 2002 Pontiac Aztek

    Not finding what you are looking for?
    2002 Pontiac Aztek Logo

    442 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...