Question about Chrysler PT Cruiser

1 Answer

Head light adjustment for a pt cruiser drivers side replace lamps low on drivers side when driving points down

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

There should be an adjustment screw or torx head bolt that will turn and raise the light

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

02 pt cruiser- fog lights aimed too low


Remove the plastic surround, use a flat blade screwdriver to pry off as usually just clipped in! Then there will be 2 or 4 screws securing the light and a single adjuster screw that pivots the light up and down, adjust the pivoting screw till desired light position is reached!

Dec 06, 2014 | Cars & Trucks

1 Answer

Where is the cam sensor location on a 2001 pt curiser


2.0 liter engine it is on the back side of cylinder head 4 bolts hold it on can be seen from drivers side of car.

Nov 09, 2013 | 2001 Chrysler PT Cruiser

1 Answer

My low light dosn't work in pt cruiser 2006


You will need to replace the headlight dimmer switch.

Apr 06, 2012 | 2006 Chrysler PT Cruiser

1 Answer

Hello. i have a 06 pt cruiser limited edition. my low beam light on passenger side does not operate,but the driverside low beam does.my high beam,tail lights directional signal all work. what could be the...


your headlight bulb may have a high & low beam filament in it, if so the low beam filament is blown & you will have to replace the bulb.......cheers

Aug 16, 2011 | 2006 Chrysler PT Cruiser

1 Answer

How do you insatll head lights for a pt cruiser 2007


Things You Will Need. Flat-head screwdriver, Floor jack, Jack stand, 1/2-inch drive breaking bar, and 19mm, 1/2-inch drive socket Adjustable torque wrench set at 100 foot lbs.



1 Park the PT Cruiser on a flat, level, paved or concrete surface.

  • 2 Open the hood to the PT Cruiser. If anything, it will allow daylight into the engine compartment and allow you to see a little better.
  • 3 Break the lug nuts loose on the front tire of the same side as the burned-out headlight. Don't loosen them too much, and don't remove them. You can try to replace the headlight without removing the tire by turning it all the way inside, but you're most likely going to find that you'll need a little more arm room to remove the door panel in the wheel well.
  • 4 Lift the Cruiser with the floor jack and place a jack stand under the rocker panel.
  • 5 Remove the lug nuts and wheel.
  • 6 Pry the tabs of the door panel in the front of the wheel well (directly behind the headlights), using a flat-head screwdriver. The panel tabs are hard rubber/plastic and more inclined to break during colder weather. The warmer it is, the more tenacious you can be about prying them out. Pry the outside one out first and work the screwdriver around the circumference of the panel to the inside tab.
  • 7 Reach inside to remove the headlight. This is a good opportunity to get up and physically look at the headlights in the front of the Cruiser. The high beams are on the inside sockets; the low beams are on the outside sockets. Make sure when reaching in from behind that you're grabbing the right bulb for replacement. Turn the headlight 1/4 turn counter-clockwise and extract it from the headlight assembly. Even with the wheel removed for the Cruiser, you're going to have limited hand room through the door panel to the headlight. If you have large hands and arms, consider recruiting someone to help.
  • 8 Unclip the headlight from the wire harness and discard it.
  • 9 Insert the new headlight into the wire harness until the lock clips into place. Don't touch the glass light bulb of the new headlight. Only handle it from the plastic plug part.
  • 10 Insert the new headlight into the headlight assembly and twist it 1/4 turn to the right until it locks into place. Test the headlight by turning the ignition key to the accessory position and turning on the headlights. Turn the key back to the "Off" position when you're done.
  • 11 Reinstall the door panel. It's going to be as much of a pain to reinsert as it was coming off.
  • 12 Replace the wheel and lug nuts. Tighten the lug nuts snugly and then lower the Cruiser to the ground. Re-torque the lug nuts in an alternate fashion, using the adjustable torque wrench and a 19mm socket.

  • Let me know if you need anything else.

    Benjamin

    Nov 04, 2010 | 2007 Chrysler PT Cruiser Touring Hatchback

    1 Answer

    I have a wrecked 2006 PT Cruiser. How do I remove the driver's side airbag to replace?


    I assume that the airbag has been deployed,and you do not have a new one as of yet.Get your new one first and that will shine a light on how it goes in.Wife has a 01 PT and it just pushes in on two steel pins that come to a point.The pins have a grove in them that snaps into two retainer clips in the steering wheel.A word of advice...replace the retaining clips in the steering wheel as well.Wife had airbag replaced then months latter was hit from behind.Air bag flew out and rite up side the head.Trust me they are not light.Ended up in rear of car.Don't skimp like the body shop did.

    Dec 31, 2009 | 2006 Chrysler PT Cruiser

    1 Answer

    My GMC truck 1993 Sierra just had new headlights installed. But the high beams point into the trees. It seems both the high and low beam lights are in one enclosure. Can I adjust these down?


    Yes you can. There is an adjustment screw at the top of each head lamp and you just turn them out or counter clockwise and the beam will come down. You may also have to adjust them side to side also. There is an adjustment screw as well.

    Aug 27, 2009 | 1993 GMC Sierra K1500

    1 Answer

    Headlight adjustment


    AIMING The head lamps should be aimed using a special alignment tool, however this procedure may be used for temporary adjustment. Local regulations may vary regarding head lamp aiming, consult with your local authorities.
    1. Verify the tires are at their proper inflation pressure. Clean the head lamp lenses and make sure there are no heavy loads in the trunk. The gas tank should be filled.
    2. Position the vehicle on a level surface facing a flat wall 25 ft. (7.7 m) away.
    3. Measure and record the distance from the floor to the center of the head lamp. Place a strip of tape across the wall at this same height.
    4. Place strips of tape on the wall, perpendicular to the first measurement, indicating the vehicle centerline and the centerline of both head lamps.
    5. Rock the vehicle side-to-side a few times to allow the suspension to stabilize.
    6. Turn the lights on, adjust the head lamps to achieve a high intensity pattern.
    9ca7b70.gif

    May 22, 2009 | 1993 Oldsmobile Cutlass Ciera

    1 Answer

    Dash instruments


    You can adjust head lights level. Up&Down.

    May 06, 2009 | 2002 Chrysler PT Cruiser

    2 Answers

    PT Cruiser Brake Light


    The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

    Jul 14, 2008 | 2006 Chrysler PT Cruiser

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    76 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...