Question about 2004 Dodge Grand Caravan

1 Answer

What direction does the top bolt on a starter turn. I can't seem to turn it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 52 Answers

Usually counter clockwise, but it could be seized and you dont want to break it, spray it with some liquid wrench penetrating fluid and let it sit a bit, or you can heat it carefully with a torch.

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove a starter


  • Remove the negative and positive lead on the battery.
  • Locate the starter under the vehicle. The starter will be located to the right of the motor on the bottom. Access the bolts comfortably from underneath the truck.
  • Remove the bottom bolt with a socket wrench. The ground cable will be attached. Save the bolt for reinstalling the starter.
  • Unbolt the positive cable on top of the starter. Use a socket wrench to remove the bolt.
  • Unbolt the top of the starter with a socket wrench. The starter will be loose.
  • Pull the starter straight out. Use both hands to pull out and forward as the starter is heavy. Pull forward and lower to the ground.
Installing the Starter
  • Position the new starter in place. Match up the starter to the designated bolt holes on the mounts.
  • Start the top bolt. Turn the bolt clockwise but do not tighten the starter down.
  • Start the bottom bolt. Ensure the negative cable is run through the bolt before starting. Do not tighten the bolt.
  • Tighten the top bolt with the socket wrench. Tighten it snug. Repeat the same for the bottom bolt. Ensure both bolts are tight.
  • Tighten the positive cable to the starter. Ensure the cable is snug to the fitting.
  • Connect the terminals to the battery. Ensure the vehicle cranks. The starter will engage without hesitation if done correctly.


Read more : http://www.ehow.com/how_5707471_replace-starter-ford-ranger.html

Dec 05, 2015 | 2006 Ford Ranger 4.0

1 Answer

Peugeot 405 srdt


There should be three bolts on the starter motor. The all face the same direction and should be in a pattern with one on the bottom, one up and to the side and one directly above the bottom one at the very top of the starter. You may have to move the exhaust pipe or certain lines to get enough room to get it out to test it. Let me know if you have questions with this. You are going to want to get it from underneath the car

Aug 12, 2008 | 1990 Peugeot 405

1 Answer

Ford 5.4 motor will not turn over new battery, starter, tried turning over by hand will turn over in one direction only but not the direction starter wants to spin


you have something in the cylinder that is not allowing the piston to go past top dead centre.. Pull the spark plugs and borrow/ buy a small inspection camera that has a lcd display and see what is stopping the piston movement. Another idea is to remove the bell housing inspection cover and look for a loose bolt or gear teeth in the ring gear that are binding up the starter pinion

Jan 06, 2014 | Cars & Trucks

1 Answer

How to take off the starter


12_29_2012_6_37_01_pm.jpg
Thats he motor its located between the engine and the firewall, mounted directly on the engine..

1.) remove the negative pole form the battery.

2.) remove the top bolt holing the starter to the engine,

3.) swing the starter down and remove the electrical wires from it, label them so you will know what goes were.

4.) remove the bottom bolts holding h starter in place.

5.) install the new one in reverse

Dec 29, 2012 | 1987 Cadillac Fleetwood

1 Answer

Where is the two bolts fo the starter motor on a mitsubishi magna


The top bolt on almost any starter is facing the opposite direction of the bottom bolt...why? I have no idea, but it's just that way...probably to releive stress on the bolts or something

Jun 11, 2012 | Cars & Trucks

2 Answers

I cannot get starter out of 1997 ford f150 all the bolts i can see are out seems stuck at top can you help


if they are all stuck and you just cant see away of getting them out then try putting a screwdriver slot in them or if possable cut the heads of and get the starter out and than remove the studs/remains ,replace with new.adrian,,,,,,,,

Aug 21, 2010 | 1994 Ford F250 Supercab

1 Answer

I have established that my starter is bad, and I'm in the process of trying to remove it. I have removed the electrical wires, and the two retaining bolts (with extreme difficulty!) but there seems to be a...


It is a 3 bolt starter for sure, And yes the bracket has to be removed, Id advise removing the oil filter as well, But it can be done without it..

Jun 13, 2010 | 1993 Ford Tempo

1 Answer

I can'nt find the top mounting bolt on my 1974 vw super beetles starter i cant seem to get to it


The starter motor is held in position by 2 bolts, the top one also secures the engine to the gearbox. The head of this bolt is a special D shape which engages into the body of the Starter motor. To undo, from the rear o/side wing, reach down behind the fan housing and you'l; find a nut (17mm) with a small amount of the bolt coming through it. Use suitable spanner to undo (turning away from you) If not been off foe a while may find that after a few revolutions all starts to turn. This just means head of bolt has become disengaged. reposition with a long screwdriver and start again.

Oct 03, 2009 | 1998 Volkswagen Beetle

2 Answers

Trying to install a new starter on a 99 Volkswagen Beetle


they have a clip thats holding the wires in,undo the clip lift the wires out and slide it off the starter

Jan 20, 2009 | 1999 Volkswagen Beetle

1 Answer

Starter


if the solenoid  is bad you can test this by taking some thing and crossing the terminals on the solenoid  and then if trying to start it dose not work it's the starter in that case remove the starter as a whole (on Toyota's is much than just removing the dead solenoid as compared to  domestic trucks) don't forget to remove the access panel on the passenger side fender well to make this go much easier and the bolts for the starter are on very bottom and top bolted directly to the bell/fly-wheel housung        

Aug 09, 2008 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...