Question about 1993 Buick Roadmaster
Typically, the entire tail light assembly has to be released from the inside. So you have to remove trim, inside, for access, usually 3 or 4 thumbscrews get released and the whole thing comes out. This set up is much more watertight than the older method of lense removal.
Posted on Mar 26, 2011
Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.
Posted on Mar 26, 2011
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Tail light removal
There is also a screw on the bottom of the light housing. You access this screw by laying on your back and reaching up behind the bumper assembly. You may also need to take one screw off the bumper mount near the tail light. This makes it easier to remove the old light housing.
Posted on Jul 24, 2008
SOURCE: removing tail light
Drop the tailgate - there are two torx style bolts holding the lens assembly in place. Remove both, then with some gentle force, pull the lens assembly straight back(there are two self seating plastic bolts that hold the assembly into the truck frame, towards the cab).
Once undone, there is a strip of three bulbs on one wired base, and that base is screwed to the lens assembly (4 phillips screws). Unscrew those, and the lens assembly is free from the base. You can then remove the bulbs, insert new ones, and reverse the process. Good luck.
Posted on Nov 07, 2008
open the trunk.
pull back the cover on the side you need to change, there are usually 3 black plastic nut you have to remove before doing this.
after the trunk interior cover is pulled off there are 3 nuts, 11mm wrench or socket will take them off. pull the taillight assembly out and twist the socket out containing the bulb that is blown. the bulb just pulls out of the socket. while the bulb is out you should inspect the socket for corrosion, it wont hurt to clean it up and put some die electric grease in there
Posted on May 19, 2009
wing nuts on innide of trunk hold lens assembly in remove all fastners and slide out assembly to access light sockets on rear of lens.
Posted on May 08, 2009
No tools needed.
Beetles: Round plug inside trunk pops out.
Beetle Convts: Grille-looking rectangular panel pops out.
Reach in and you'll feel a large finger-grip able nut, back it off (DON'T DROP
IT) and place it somewhere retrievable. Take a small-flat-bladed screwdriver and wrap it in cloth so you don't scratch the paint. Poke said protected blade between the inside body joint and the tail light, gently pry tail light out. Remove offending bulb, replace with new. Installation is, as they say, the reverse of removal.
Posted on Jul 16, 2009
Tips for a great answer:
Feb 06, 2012 | 1998 Mitsubishi Lancer
Apr 15, 2010 | 1986 Chevrolet Camaro
Jul 16, 2009 | 2003 Volkswagen Beetle TDI
Jul 04, 2009 | 2008 Hummer H3
Jun 08, 2009 | 2005 Chevrolet Impala
Mar 31, 2009 | 2006 Dodge Stratus
Feb 17, 2009 | 1996 Cadillac DeVille
Jan 13, 2009 | 2004 Infiniti G35 Sport Coupe
Dec 16, 2008 | 2002 Isuzu Axiom
May 30, 2014 | 1993 Buick Roadmaster
232 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: