Question about Peugeot 405

1 Answer

Press button on key and nothing happens doors wont open or lock on my peugeot406 i have had my battary checked on fob it ok

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 510 Answers

Synchronization
When
Key battery replaced. If buttons operated repeatedly while vehicle out of range and system becomes inoperative.
How
Switch ignition ON. Press and hold lock button Fig. 1 [1] for 10 seconds. Switch ignition OFF. Remove key from ignition switch. Wait 5 seconds. Synchronization procedure complete. Confirm synchronization has been successful by locking, double locking and unlocking vehicle. Repeat above procedure to synchronize any remaining keys.
Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys. Obtain owner's vehicle security card. Replacement keys can only be programmed using diagnostic equipment.

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 ES 350. Changed key fob battery,now nothing works. Only immobilizer security light is flashing and engine start stop button has amber colored light on


Be sure to use the correct battery, properly in place, clean the key contacts , See owner's manual for additional information.
There are specialized locksmiths for car keys

Oct 02, 2014 | 2007 Lexus ES 350

1 Answer

03 passat key/ fob not working battery ok


How much freon does a 96 Honda accord LX hold?

Jul 09, 2013 | 2003 Volkswagen Passat

1 Answer

My renault clio 1998 r reg key fob wont work


hold the cetral locking lock all button down until the doors lock and unlock. The imobilser light goes solid red. At this point you have 10 to press the botton on your key 2 times . the doors will unlock and lock.

Mar 27, 2012 | Cars & Trucks

1 Answer

Keyless entry remote wont progam


It will not unlock the door the first time you push the button. This only registers the key fob ID into the computer. When you press the button on the key fob, press it only once and wait for the hazzard lights to flash twice again. Then open the driver's door. The key fob will not become active until you open the driver's door.

If your hazzard lights do not flash after you press the button on the key fob, there is most likely a problem with the key fob. Either it is not the correct key fob for your vehicle, or the battery is not in correctly or the key fob is defective.

The only other advice I can give you is to have it programmed with a scan tool. This way, the scan tool can verify that the computer in your vehicle is receiving the signal from the key fob.

It can be done either way, but if the "no scanner" way does not work, the rest of the system should be checked for possible problems.

Dec 12, 2011 | 2005 Nissan Altima

1 Answer

When i lock al my doors on my 2004 Chrysler pacifica from my keychain all doors lock except for the driver door. The alarm is still activated but if someone tries to open the driver door it will open and...


This can happen If you have used the IGN. key to unlock the drivers door after you locked them from the fob. This can also be caused by a stuck button on the drovers door. Check the drivers door all buttons to see if any are stuck. If you do not have any stuck buttons. Try this, from inside the car, with out the car running, use the button on the drivers door to "lock all doors". Then use the fob to unlock them, then get out and press the lock button on the fob twice real quick. This should cause the drivers door to lock as the others. Hope this helps Fix Ya Up.

Jul 03, 2011 | 2004 Chrysler Pacifica

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

1 Answer

Chevrolet blazer 2001 programming transmitter FOB


lol...turn the key on..there a reset button on the dash that show mile how far u drive..well push and hold while the ignition on and engine off until it blink..than start tap it until you came across door lock/alarm...ok ...here the trick..leave the setting on the alarm. than u can press an hold unlock n lock until u hear the door lock than u release turn key off n on than off again...and than try your transmitter

Apr 21, 2010 | 2001 Chevrolet Blazer

1 Answer

HELP HELP !!!!!!! Electric fault i think !!!!!!!!!!


1....ensure the battery in the "Key Fob" is OK............Press either Lock or Unlock button for more than 1 second, the lamp on the fob will light if OK. Change battery if it does not illuminate! 2.....if battery on fob OK.......Re Syncronise the key fob to the car by:.... a brief press on either button twice and within 30 seconds turn Key to position 2 on the ignition lock
Hope that fixes it...let me know?

Nov 09, 2008 | 1998 Mercedes-Benz C-Class

3 Answers

Mercedes S320 central lock


if you hav a remote control key &yr car wont respond . change key batrrey &contact dealer if still dont work for software

Jul 13, 2008 | 1994 Mercedes-Benz S-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

336 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...