Question about 2004 Dodge Ram 2500

1 Answer

Right front axel seal replacement how to - 2004 Dodge Ram 2500

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 133 Answers

You have to remove the wheel bearing and axleshafts from both sides. then remove the carrier from the differential. use a long bar to knock out the old seal then press in the new one

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace right front axel seal 2001 pathfinder


Hi,if you are talking about the drive shaft cv boot,there is a vidio on you tube showing how to change the drive shaft same perseger,hope this is helpfull,all the best,its a easy fix.

Oct 03, 2015 | 2001 Nissan Pathfinder

1 Answer

How Do I replace front axel seals


Now can you buy whole axel and change.

Oct 13, 2014 | 2005 Dodge Dakota Quad

1 Answer

Ive got a 1989 k1500 and the right front inner axle slides in and out about an inch or two. so that means the spring clip isn't on the end of the axle. I'm told I can replace the clip by putting it on the...


first off do you have the other clip from the axel?or do you know were it is? if it's not in the diff then yes just tap the axel in with a dead blow and try not to damage the axel seal

Sep 29, 2010 | 1989 Chevrolet K1500

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

I need help with Axles for 2001 Hyundai Elantra. The Left Axle rubber cover is broken, also I heard noise when the wheel moves iether left or right turn when the car is leaving or entering a parking box....


depending on how bad the axels are. you could buy new ones. or you can buy a rebuild kit. now for the leak just 1 seal but if your gonna remove both axels i suggest buyin both side seals.

Jul 22, 2009 | 2001 Hyundai Elantra

1 Answer

1999 dodge cummins 2500 front axel seals


you need to pull off wheels,brakes, rotor /unit hub bearing, both axles and intermediate shaft, as well as the vac disconnec ton the front axle tube. if only the right side leaks then only then only pull the right axle and intermediate shaft and vac disco. it is a trick with a miller tool to replace the seal. the left side seal is inside the diff and the carrier has to come out to replace it. pete

Jun 09, 2009 | 2004 Dodge Ram 2500

1 Answer

Front axel will not go back in after seal replacement


you need to aline the spline then is will go in

Jun 06, 2009 | 2003 Chevrolet Tahoe

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

LEAKING FRONT AXIL SEAL


take the wheel off , unbolt caliper and sling it out of the way with a bungi cord, take off the rotor, then you have too take the pumpkin cover off the axel diff in the front (drain fluid first) easy way to do that take out bottom and side bolts out then leave top 1 or 2 in but finger loose. pry cover off with a sturdy scrapper from side allowing fluid to leak out from bottom of cover. when fluid is done comeing out then take off cover. to take the axel out to replace the seal you have to push the axel inwards to remove the C- CLIP on the end of the axel shaft that slides into the inside of the pinion gear (use a extending magnet) keeps gear oil on your hands and from dropping it into the pumpkin housing. then all you have to do is slide the axel shaft out. then replace the seal .

Jul 01, 2008 | 1990 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...