Question about 2002 Mercury Sable

1 Answer

Had new pads installed in the front and rotors were turned. Now I hear a sound as if one of the brakes pads touching the rotor. It stops when I bearly apply the brakes. Sometimes If I ride the brakes It sounds like woof, woof, woof. What is wrong? Larry....

Posted by on

Ad

1 Answer

Without going into all sorts of detai,l of
how brake work should be performed

I will say something wasn't done correctly &
you need to go back and find out what

I would guess that no rust was removed from
any components, and you new machined rotors
do not run true

You really need to do all you own vehicle work,
if you want to avoid this sort of poor professional
work, that is all over the industry

Posted on Mar 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota highlander front wheel noise when turning left


Check the brake rotor backing plate to see if it is rubbing against the brake rotor, check the brake pad condition at the same time, it may be the low brake pad sensors that you are hearing.

Nov 03, 2012 | 2005 Toyota Highlander

1 Answer

2003 Lexus es300 has high pitch squeel in front driver side tire, stops when brakes are applied or when I turn the wheel


u need front brake pads...the noise u hear is a warning sensor that is on the brake pad...it will touch the brake rotor when the brake pads r getting very low an about ready to start grinding into the brake rotors

Jul 16, 2011 | 2003 Lexus ES 300

2 Answers

My brakes sound like they are grinding


check rear rotors and front rotors for rust buildup (flahlight helps). does the vehicle shake when you come to a hard stop? You will either need to have a front or rear or both brake job (rotors cut or replaced and new brake pads) If the vehicle is shaking when coming to a stop, its probably your front pads. If your hearing the noise from the rear its the rear pads or it you hear it from the front its the front pads. If there significant rust build up or your pads are low a brake job is recommended.

May 04, 2011 | 2008 Nissan Armada

3 Answers

Escalade Grinding sound coming from left front when stopping


Most likely cause would be disc brake pads grinding against brake rotor.

Mar 02, 2011 | 2005 Cadillac Escalade

2 Answers

I have a Hummer H3. I hear Noise from wheels while turning & doesn't stop. Also I hear a grinding noise when I hit the brakes. Dealer had to resurface rotors. Problem started at 15000 miles. Took it...


Ranjit,

I have the same problem with my 2008 Hummer H3. I had the front and rear rotors resurfaced. I am now thinking of getting the rotors replaced with bigger more durable rotors. Solution about the sticking brake caliper sounds about right if you hear a grinding noise as you drive without even touching the brake pedal.

Amardeep

Feb 18, 2011 | 2008 Hummer H3

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

4 Answers

Brakes and rotors making noise


Were metallic brake pads installed? If they were and are hidhly aggressive, yes. Give them a few miles to smooth out.

Jul 29, 2009 | 2000 Pontiac Grand Am GT

2 Answers

Pulsing sound and feel from wheels


Ok, if the wheel bearing assembly was installed incorrectly the wheel would wobble and you would have a disconcerting feeling in the steering wheel. The rotors have to be within factory specs to be turned safely. What I would do is have the rotors checked with a micrometer and replaced.

Apr 01, 2009 | 2002 Pontiac Grand Prix

1 Answer

Front brakes problem


DO THE ROTORS HAVE A LEFT AND RIGHT SIDE? POSSIBLY INSTALLED BACKWARDS? ASK THE PARTS STAORE ABOUT LEFT & RIGHT SIDE ROTORS & DO HAWK PADS CLASH WITH ATE ROTORS? POSSIBLE DEFECTIVE PADS?

Jan 13, 2009 | 2004 Honda Odyssey

1 Answer

Front brakes binding and grinding


Sounds like your brake calibers are sticking. Get new ones and new pads. You probably should get new rotors also because with the dragging calibers they most likely got hot and are warped. Search on ebay and www.rockauto.com . I personally use power stop drilled and slotted rotors with mid grade pads. You can probably get a whole kit.

Oct 22, 2017 | 2000 Ford Windstar

Not finding what you are looking for?
2002 Mercury Sable Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...