Question about 2006 Hyundai Elantra

1 Answer

I have 2006 hyundai elantra with a bad camshaft sensor. I have part on hand. Anything special I need to do besides swap out the part? Cam Shaft Location?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

I assume you determined the diagnostic trouble code for the sensor was TRUE/VALIDATED?
If so, then there is NO reason to do anything else but 'swap out the part.' Your second question is somewhat puzzling... the cam shaft is on TOP of the engine - the sensor's location (standing on the passenger side of the vehicle with the hood open, is on the left side of the engine at approximately the 10 o'clock position of the cam.... the connector to it is at the 9 o'clock position.

Posted on Mar 26, 2011

  • shawn_pirz
    shawn_pirz Jan 31, 2014

    The mentioned location is for crankshaft sensor I believe on a 2006 Elantra GLS

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing marks for 2006 hyuandai elantra 4cyl


Go to YouTube, type Elantra Timing belt replace. There are a few videos that will show cam and crank timing marks. Very helpful stuff.
Good luck

Sep 30, 2017 | Hyundai Elantra Cars & Trucks

1 Answer

Hyundai 1.6 Elantra gls, does the spark come from the cylinder head or the crank shaft


neither
the crank shaft position sensor triggers the ignition control module that generates the spark either internally or through a coil/ pack
the cam position sensor ok, s that process to prove that the cam shaft is turning correctly

Apr 13, 2017 | Hyundai Cars & Trucks

1 Answer

Where is the cam position sensor on a 97 Hyundai elantra


Hi Zolo,here's a link to your camshaft position sensor. Duralast Camshaft Position Sensor SU4117 ReadReviews onDuralast SU4117 The Camshaft Position Sensoris located: Under hood, passenger side, upper engine area, mounted in engine block .Here's another on how to replace it.
Repair Guides Electronic Engine Controls Camshaft Position cmp Sensor...

Sep 28, 2016 | Hyundai Cars & Trucks

1 Answer

Ck engine light stays on. Autozone says it is the camshaft sensor. I have pulled it apart and cleaned it with a qtip and alcohol, reset the battery and it has worked great. Now, it doesn't and my...


Gas milage (economy) is dependent upon the O2 Snsr's (oxygen Sensors) input to the ECU (Engine Control Unit). The cam position sensor, if malfunctioning, it should be replaced (cleaning it doesn't repair the problem which exists inside the component/sensor). Before you start throwing money after parts, Have a qualified/certified Hyundai Service Technician properly diagnose this issue.

Sep 10, 2011 | 2006 Hyundai Elantra

1 Answer

Camshaft sensor


Cam sensors usally are in the distributer.

Jul 20, 2009 | 2004 Dodge Stratus

1 Answer

Error code po340 for a 2002 hyundai elantra


Here is what I could find on your P0340 error code:
CausesA code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible SolutionsWith a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
Sounds like since you have replaced both the camshaft and crank shaft sensors you need to look at the PCM.  Go down the line of possible solutions and don't replace the PCM unless nothing else works obviously.  I hope this helps but it looks like you are looking at getting a new PCM.  Good luck.  Thanks for rating my response and for using FixYa!

May 27, 2009 | Hyundai Motor 2002 Elantra

1 Answer

Camshaft postioning sensor


On 1995 and later models the CKP is located at the rear of the engine near the transaxle bell housing.

Sep 30, 2008 | 2004 Hyundai Elantra

Not finding what you are looking for?
2006 Hyundai Elantra Logo

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...