Question about 1993 Ford F350

1 Answer

Where is the location to put 90 weight oil in rear end?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

There should be a plug about mid way up on the rear of the diff off center to the right

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What type of oil or additive do I need for my 1992 Chevy Blazer's posi rear end?


Find a 90 weight gear oil from your local auto supply store. It's thicker then your conventional motor oil.

Jan 28, 2015 | Cars & Trucks

1 Answer

Need to change rear seals in axcles how to? 98 gmc jimmy


First i would check to see if the axle air vent was clear if its not the oil is vary heavy and expands a lot this will build up pressure inside the houseing and cause the axle seals to leak if you can clear it the problem may fix it self its 80 90 weight oil thats thick stuff. If not you need to remove the rear wheels and brake drums then you have to remove the cover from the rear carriar catch the oil. Look inside the carriar houseing you will see the ends of the axles theres a small clip on each axle called a c clip remove them you can pull them out with your fingers. Then you can slide the axles out past the brake plates pry the seals out you might as well replace the bearings when your doing but thats up to you. Lube and install the bearings then the new seals you will need new seals lube the seal lips and vary carefuly slide the axle in taking care not to damage the seal install the c clip do the other side put a new gasket on the rear carriar tighten bolts to 20 ft lbs. Refill carriar 80 90 weight oil through filler plug on the side of the houseing until it just starts to run out hole put the plug in the rear drums on and wheels

Dec 30, 2010 | 1998 GMC Jimmy

1 Answer

How do I grease the rear axle of my 01 chevy blazer (2wd) until I can get the leaking seal replaced?


Replace the seal forthwith. leaking grease will wreck your brakes and that is dangerous.

Typically rear ends take 90 weight oil, it goes in through a plug near the center of the rear end, fill to bottom of the hole, with rear end level. You can get a suction gun to **** some fluid and pump into the rear end.

Nov 11, 2010 | 1989 Chevrolet S-10 Blazer

3 Answers

What type of oil is used on grang cherokee ltd rear differential


depends on the diff. highly recomend the factory oil from the dealer. those rear ends have enough problems as it is so dont compound things by putting in an inferior oil. also get the friction modifier aditive with it. it used to be [2004] the oil didnt come with it.

Apr 15, 2010 | 1997 Jeep Grand Cherokee

1 Answer

I need to know what type of oil to use in the drive shaft yoke? for an Isuzu pickup 1995 with a 2.3 L FI engine.


You mean the rear end? 90 weight gear oil. Regular or Synthetic. Considering the year of the truck, regular will out last the truck. Most people never change gear oil. Hope this is what you are talking about.

Apr 03, 2010 | 1995 Isuzu Pickup

1 Answer

What oil is recommended for a split rear end axle.


You need to run 90 weight or 70-90 weight plus friction modifier if you have limited slip.

Mar 17, 2010 | 1990 Ford F350

1 Answer

Need to put oil in the rear of car thats 90 weight need to no where it goes


Take it to an oil change place and tell them to check the differential oil. It won't cost much and trust me, it's hard to do at home without a lift.

May 29, 2009 | 1992 Ford Tempo

2 Answers

Ned to change the oil in transfer case


The Z71 typically comes with the auto 4wd transfer case (cannot remember the GM number). This requires AutoTrak II, which is available at a GM dealer. Do not use any other fluid in this transfer case! The previous post was correct in the location of the two plugs, but not on the fluid (the other types of transfer cases by GM use ATF). The transfer case is located under the truck right under the cab. There is a small skid plate under it, and a large driveshaft leaves the rear end of the case heading to the rear differential (axle). If you have the manual or electronic w/o auto 4WD transfer case, you can use Dexron III, but Dexron VI is a better fluid that is also now available at your local auto parts store. Again, if you have the AUTO 4WD button in the dash, use the AutoTrak II fluid from the dealer.

Apr 19, 2009 | 2003 GMC Sierra 1500

Not finding what you are looking for?
1993 Ford F350 Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...