Question about 1999 Acura TL

1 Answer

The passenger rear tire will not come off, and the lugnuts have been removed, how do we get this tire off?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 3,640 Answers

Smack the rim from behind tire and it should pop loose.

Posted on Mar 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im trying to replace my passenger side front lugnuts


jack up vehicle, remove tire, Beat on broken lug till it falls out- install new lugnut (will be pressure fit) replace tire and tighten nut....make sure you tighten it 2 times at first then after 50 miles check it again.

Dec 09, 2013 | 1997 Plymouth Grand Voyager

1 Answer

Need to romove and replace sheared lugbolt on rear driver side wheel hub


remove tire...if it has disc brakes remove caliper/pads and rotor...if it has a drum break remove drum..Now take a punch and hammer and hit the center of the lugnut stud untill it pops out the back.put the new one in and get it tight with the lugnut.Replace brakes and tire and tighten that lugnut until it stops.Then check it in 500 miles

Jun 06, 2011 | 1998 GMC Jimmy

1 Answer

How to lower spare tire


Find a plastic cover located in the carpet at the back right corner. Lift the cover to locate a nut the size of a lugnut of your tires. Using the van's lugnut wrench, turn nut counter-clockwise to lower the spare tire. Have fun and don't pinch yourself while removing the tire.

Oct 14, 2010 | 2004 Ford Freestar

1 Answer

Looking how to lower spare tire on toyota sienna van


Hello. Welcome to FixYa! Please allow us to assist you.

The procedure is as follows, to remove the spare tire from a 2WD Sienna:

Move the passenger seat as far forward as possible.
Move the passenger side middle seat back as far as possible.
Obtain your tire tool (the one you would use to remove the lugnuts)
Observe the carpeting behind the front passenger seat; you will see a small piece of carpet, like a small 'flap', that can be raised.
Under this flap is a small silver 'bolt'. Fit the lug wrench onto this bolt, and rotate it. This will lower the cable that raises the spare tire up under the area between the passenger front and rear seats.

Note: 4WD Siennas do not have any spare tires, as they came with 'run-flat' tires. Toyota did not fit a spare on the 4WD units.

Thanks for choosing FixYa for assistance today.

Jun 10, 2010 | 2008 Toyota Sienna

1 Answer

Removed all lugnuts something still holding tire on. didn't have this problem with rear tires just the front.


make sure its blocked up then craw underneath and hit the back of the rim with a big hammer ,its just corried together !!

Mar 22, 2010 | 2007 Dodge Nitro R/T New Cars

1 Answer

My left back tire of a 1991 Lincoln towncar fell off & i was trying to replace rear lugnuts studs


remove all brake components off of that side, pound out studs towards center of the car with a hammer. place the new studs through the back of the axle and then use washers that just fit over the studs for spacers, and put the lugnut on the stud and tighten until the new stud is seated on the back flange of the axle. remove the lugnut and repeat for the rest of the studs.

Mar 20, 2010 | 1991 Lincoln Town Car

1 Answer

Changing a flat on a 1998 chysler cirrus


Get a four way lug wrench that and loosen, but do not remove, all the lugnuts on the wheel that has the flat.Next, jack up the car by lifting it up from the side underneath the doors on the pinchweld.Then remove the lugnuts.Install the spare after removing the flat.Tighten the lugnuts till they are snug on the wheel,then lower the jack .Then torque the lugnuts tight after the car is back on the ground, and you're ready to go down to the tire shop to get the flat fixed.Hope I could help!!!!

Feb 01, 2010 | 1998 Chrysler Cirrus

Not finding what you are looking for?
1999 Acura TL Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...