Question about Ford Windstar

1 Answer

Hi my name is Jessica, today I noticed that my 2000 Ford Windstar started shaking when I come to a stop, and is really slow to accelerate, any help would be sinserly appreicated..

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Sound like you have a brake issue when you apply the brakes sounds like a rotor may be hanging up not letting go causing the van to be sluggish to take off holding it back

Posted on Mar 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 windstar with a 3.8 motor cranks slow then stops and no start .Acts like a dead battery battery is good what can it be?


Bad connection or corroded cables, possibly a bad starter. Sounds like something is drawing more amps than the battery is capable of supplying.

Dec 21, 2015 | 2000 Ford Windstar

1 Answer

200 windstar with a 3.8 motor cranking very slow then stops cranking and does not start


Could have a bad cable , to check voltage drop starter circuit ! Starter Voltage Drop Watch some other voltage drop testing videos ! You need a DVOM - digital volt ohm meter to do this testing .

Dec 21, 2015 | 2000 Ford Windstar

1 Answer

I have a 2000 ford windstar van. When I crank it up it shakes very bad but once I take off the shaking goes away but it replaced with a vibration in the steering wheel and once at the stop light it starts...


you might have a vaccume leak or the mar sensor may need cleaning if it's a fuel injected setup i really need engin size to get a better line on problem try you tube also.

Feb 21, 2015 | Ford Cars & Trucks

1 Answer

2000 ford windstar shakes only when accelerating and sometimes at stops. no cel codes


Have it checked for stored codes, with a professional
scan tool

You don't need MIL Lamp lite on dash, to have problems

Probably have a cylinder misfire that doesn't set a light
on your dash or one of six other possible issues

May 29, 2012 | 2000 Ford Windstar

1 Answer

Car shakes when accelerating and at stops sometimes


Well sounds Like TIRES Or JUst MAybe DRIVESHAFT look for Being Loose maybe worn out bearing replace drive again look hard at them Carefully

May 29, 2012 | 2000 Ford Windstar

1 Answer

Our 2000 Ford Windstar has developed a shudder and knocking when accelerated or in a strain (like uphill). The problem seems to be located on the driver's side and from the sound (Knocking) seems to be in...


Look at your motor mounts ( very likely), a bad tire on the driver's side, or perhaps a worn strut or some other worn out suspension part.
God bless your efforts.

Sep 07, 2017 | 2000 Ford Windstar

1 Answer

Shaking when idle, stops or slows shaking when i accelerate


ck fuel filter could of sucked up something from the bottom of gas tank,,could have fowl spark plugs,,

Jan 29, 2010 | 2000 Chevrolet Lumina

1 Answer

2000 Ford Windstar 3.8L error P0401 then P0404


if the check engine light is blinking,you have a misfire(spark plugs,plug wires or coil pack.inspect the plug wires for damage.The rear bank plug wires (at the fire wall) get alot of heat and the boots will crack, causing a misfire.You might want to have your local shop check it for you,to see if there is an open circuit or shorting in one or more of the plug wires.if it has been awhile since a tune-up,you might want to do that first,and inspect the plug wire boots also and replace them if needed.

Oct 24, 2009 | 2000 Ford Windstar

1 Answer

2000 Focus has engine "shake" and won't idle


Always start with check engine issues first and repair them,then move on to no code symptoms. Go to shop with a good scan tool ,not a $200.00 auto part store frebee and no code book

Sep 28, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...