Question about Ford E-250

1 Answer

I need to replce my rotor's on an e-250 van. How do I remove them?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

Place van in park and place chocks behind the rear wheels. Jack up the van and place two jack stands underneath the frame. Remove the front tires. Loosen the bolts holding the caliper assemblies and use a large flat screwdriver to pull the caliper 1/16 in. Remove the bolts holding the calipers and pads and set the assembly up out of the way. Do not put any strain on the brake lines. Take off the bearing caps. Remove the cotter pins and wheel bearing nuts. Pull the rotors off. Inspect and have them machined or replace them with new.

Posted on Mar 25, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear rotors on a 2010 Ford E250 are stuck. Need tips for rotor removal.


WD40 AND A GOOD HAMMER, make sure the emergency brake is released and spray the hub and tap on the rotor and you might look to see if the rotor has two holes in between the studs and if it does then screw two 5/16 bolts in and the hub will come off

Dec 16, 2016 | 2010 Ford E-250

1 Answer

Need a routing diagram for a 2004 ford e-250 carrier coach van


there should be a decal under the hood somewhere that shows the belt routing.

Aug 28, 2014 | Ford F-150 Cars & Trucks

1 Answer

91 dodge passenger van 250 318- new plugs/wires/dist/rotor cant seem to figure out why it falls on its face at takeoff & lurches @ exeleration&deceleration!!!!! help


Could be a number of things, bad computer, fuel pump, electrical failure somewhere in system, poor ground fault, the list goes on

Mar 29, 2014 | Cars & Trucks

1 Answer

No spark


A mechanic would first check the ASD relay and make sure the coil has voltage. I assume you have checked the cap and rotor and you are not getting spark from the coil tower.

Aug 21, 2012 | 1987 Dodge 600

1 Answer

Brake shoes on 1987 f250 460 1987 2 wheel drive how to replace


Lift the front of your Ford F-250 off of the ground using a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench to prepare the truck for servicing. 2 Open the hood on the engine compartment and take the lid off of the master cylinder that bolts to the brake assister on the driver's side firewall.3 Remove the hex-head bolts on the back of the brake caliper with a socket. With the bolts removed, pull the caliper off of the Ford's brake rotor.4 Pull the old brake pads out of the caliper and discard them. Squeeze the brake piston back into the backside brake caliper with pliers, and then insert the new pads into the brake caliper.5 Pull the rotor cap cover off the middle of the rotor with a screwdriver and use a socket to remove the nut located behind the cover.6 Pull the rotor off of the wheel spindle.7 Remove the old wheel bearings from the brake rotor and insert them into the new rotor. If the old wheel bearings are worn, replace them with new bearings.8 Slide the new rotor onto the wheel spindle and secure it using a bolt and socket. After you tighten the bolt, press the cover back onto the rotor.9 Place the caliper on the rotor and secure it with a socket and hex-head bolts. 10 Duplicate the process on the passenger side of the F-250. 11 Close the master cylinder after putting the wheels back on the Ford and lowering it to the ground. Press on the brake pedal to seat the pads against the rotor
Replace the F-250's Rear Brakes 1 lift the rear of the Ford F-250 off the ground with a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench.2 Place a strip of paint on the back of the brake drum and rear brake drum cover so you can position the brake drum orrectly when you put it back on. If you plan to install new brake drums on your Ford F-250, skip this step. 3 Place the brake drum puller on the brake drum and pull the drum from the wheel hub. The method for attaching the brake drum puller depends on the brake drum puller that you use. 4 Remove the springs that attach the brake shoes to the wheel hub by pulling them off with pliers.5 Lift the old brake shoes off of the wheel hub and place the new brake shoes on the wheel hub. Secure the new shoes with the springs.6 Pound the brake drum onto the axle hub with a rubber mallet.7 Duplicate the process on the passenger side of the Ford.8 Put the wheels back on the F-250, lower it to the ground and, then press on the brake pedal to seat the shoes against the brake drum.

Oct 14, 2011 | 1988 Ford F 250

1 Answer

Trying to find fuel pump on my '84 G30 1 ton van with a V8 350 5.7 liters engine? And whats the best way to replce it?


Trying to find?

Best Way?

Almost all fuel pumps are in the fuel tank

You have no choice but to remove the tank,
then remove the pump from the top.

A'm I missing the question?

Jun 30, 2011 | Chevrolet G30 Cars & Trucks

1 Answer

I need to reploce the front left rotor on a 1996 ford econoline van. I need to know how to remove the bearings from the old one and put in the new one. Plesae help


Once you remove the center cap, remove the cotter pin, and remove the nut and washer, the outter bearing should slide right off. Remove that, and put the nut back on, then pull the rotor towards you, allowing the nut to touch the top of the inside of the rotor, until you catch the inner bearing on the nut, then give a ****, that should leave the bearing and seal left on the spindle. If not, you can use a seal remover, to get out the seal and the bearing will fall out of the rotor. Pack the new bearings and install the inner bearing, tap in the seal in the rotor, install rotor, install packed outer bearing and install.

Mar 12, 2010 | 1996 Ford Econoline

1 Answer

Changing front rotors 2002 astro


YOU HAVE TO SAFELY RAISE SUPPORT VAN ON JACK STANDS.REMOVE BRAKE CALIPER AND BRAKE PADS DONT DISCONNECT BRAKE LINE.THEN MOVE DUST CAP OR GREASE CAP.REMOVE COTTER PIN SPINDLE NUT AND WASHER.THEN THE ROTOR NUT.YOU NEED A HAYNES OR CHILTON MANUAL.BECAUSE YOU HAVE TO ADJUST WHEEL BEARING WHEN YOU REPLACE ROTORS.

Feb 01, 2010 | 2002 Chevrolet Astro

2 Answers

Replacing brakes & re-surfacing rotors 4WD f-250 1991


need to know if the hubs are auto locking or manual. the bearings have different locking set ups.

Mar 23, 2009 | 1991 Ford F250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...