Question about 1992 Chevrolet K1500

2 Answers

Where does the horn relay go ? - 1992 Chevrolet K1500

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

In the convinience center underneath the dash to the left of the steering column, against the firewall.
The horn relay is to the right of the turn signal flasher, and is a bit smaller in size.

Posted on Mar 25, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Where does the ignition relay go

Posted on Jun 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is horn relay for sc1 1.9 4 cyl. saturn 1999


The horn system consists of a single horn, a horn relay located in the underhood fuse block, and driver controlled horn switch in the steering wheel. The horn system is designed to provide the driver with an audible warning to signal pedestrians, other drivers, etc.
Operation
Voltage is supplied to the horn relay coil and contacts at all times through a 10 amp HORN fuse, located in the underhood fuse block. When the driver pushes the horn pad, driver air bag module, the circuit completes and energizes the horn relay coil. This causes the horn relay contact to close. When the contact closes, current travels to the horn and the horn emits an audible warning.

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

How do I fix the horn on 2006 Impala


System Description
The horn PCB relay is non replaceable ,soldered to the underhood fuse / relay box. . You would have to take the box a part to get at it . Is the air bag light lit on the instrument cluster ? Could have an open wire in the Clock spring , do you know what a clock spring is ? It is inside the upper part of the steering column , It allows the steering wheel to be turned full right to full left keeping the horn an all the buttons an air bag connected electrically. When the horn button is pressed, ground is applied through the horn switch contacts and the horn relay control circuit to the coil side of the relay. The horn relay coil is then energized, causing the relay switch contacts to close applying voltage through the horn control circuit to the horns. For theft deterrent functions, the body control module (BCM) also controls the horn relay by applying ground to the relay control circuit to the relay.
Circuit/System Testing
With a test lamp connected to ground, probe each of the test points on the HORN fuse while activating the horns. The test lamp should illuminate at one or both of the fuse test points.
?‡'
If the test lamp does not illuminate at either test point, refer to the Horn Switch Test.


?‡'
If the test lamp illuminates, refer to the Horn Test.


Ignition OFF, disconnect the inline harness connector C275. Ignition ON, test for B+ between the horn relay control circuit terminal B and ground.
?‡'
If less than B+, test the control circuit for an open/high resistance. If the circuit tests normal, replace the underhood fuse block.

Momentarily connect a 3-A fused jumper wire between the control circuit terminal B and ground. The horns should work.
?‡'
If the horns do not work, replace the underhood fuse block.

If all circuits test normal, test or replace the horn switch

The PCB relay horn system consists of the following components:
?€¢
Horn switch

?€¢
Horn PCB relay

?€¢
Horn assembly

?€¢
Body control module (BCM)

?€¢
HORN fuse 15 A

How cars clock spring works

May 17, 2016 | 2006 Chevrolet Impala

1 Answer

1995 accord horn not working.hear horn relay clicking but no current at horns when checked with test light. bad horn relay?


Check your wiring diagram and check for power coming out of the horn relay. Suspect a bad relay.

Oct 26, 2014 | 1995 Honda Accord

1 Answer

Location horn relay on 82 cj7


The horn relay primary receives + full time and is actuated by receiving ground (-) from the horn button. Check ground continuity at the horn button (at the steering wheel) to make sure it is working first (most likely culprit). If the horn button is working, check to see if the horn relay is working (second most likely culprit). To test the horn relay, provide chassis or battery ground to the (-) primary terminal of the horn relay and see if the horn honks. If it does, that will tell you that the problem is in the wiring between the steering wheel and the relay, most likely a disconnected wire at the steering column.
The only other components in the system are the fuse for the horn circuit (if you have 12v at the horn relay, that is fine), and the horn itself. My bet is on the horn button pad itself.

May 25, 2014 | Jeep CJ7 Cars & Trucks

1 Answer

Car horn not working


as with all elect. fails check all fuses
in this case the 15 amp fuse marked, HORN
can i presume all else works good> car drives.?
all answers, USA spec car. nobody ever tells location, so..... if not USA< all answers wrong. the usa car has just 1 horn.....
got voltage to horn? 12v
Yes or no.?
if yes horn bad.
got voltage from horn relay
yes, bad wires.from, relay to horn
no, got voltage 12v to horn relay coil,
yes, good, no bad fuse.
got 0v to other relay coil (all tests honking)
yes, bad relay.
no, bad horns switch.

if you want me to guess. sure.
1: bad wires ../connections, end to end.
2 bad horn
3: bad relay
4: bad horn switch.

Dec 27, 2013 | 2005 Toyota ECHO

2 Answers

Horn doesnt work all fuses and relays are good


If you know the fuse and relay have power, you should be able to jumper the relay and make the horn blow. The horn pad on the steering wheel usually grounds the relay. If you can jumper the relay and make the horn blow, the problem may be the horn pad or the clockspring in the steering column.

Sep 25, 2012 | 2003 Chevrolet Silverado 1500

1 Answer

TOYOTA ECHO HORN


The problem is one of three possibles:

  1. The horn switch (button) on the steering wheel.
  2. The horn relay.
  3. The wiring associated with the two items above.

If you press the horn button and know where the horn relay is, you can listen for it to activate. If it does, then either the relay's output contacts are bad or the wiring between the relay and horn is faulty. If the relay doesn't activate, test for voltage at the relay coil with an multimeter in the relay socket. If there is voltage there when the horn button is pressed, then the relay is bad. If there is no voltage there, the the horn button or associated wiring is faulty.

Jun 02, 2012 | 2001 Toyota Echo

1 Answer

Horn


No the Chevy Malibu is not made by Kia!
I think you mean horn relay
I would try a new relay it is possible that the relay is defective and that's why it was removed
here is how the horn circuit works
The body control module (BCM) controls the horn relay by grounding the control circuit of the horn relay coil. When the horn relay coil is grounded, the horn relay contacts close, applying voltage to the horn via the horn supply voltage circuit.
if the horn relay does not fix your concern you may need to take it to a shop and check for any BCM fault codes
and you are correct having no horn is a SAFETY ISSUE
that car should have NEVER PASSED A SAFETY WITHOUT A HORN
hope this helps good luck and I hope the relay fixs it because a BCM is costly

Jan 23, 2010 | 2005 Chevrolet Malibu

2 Answers

Horn makes a clicking noise when i push the horn switch, but does not make a honk noise, what can be the problem?


The horn relay is faulty or the horn is dead.Try tapping on the horn while someone is holding in the horn button,if that make the horn work the it's the horn,if not,change the relay.

Oct 23, 2009 | 1994 Honda Civic

2 Answers

Position in car of the horn relay


one relay is going to work both horns if there are two horns.
horns are different than relays.
all horns are ran from one relay.
the horns are only different in sounds.
if one horn is not working and the other is its the horn itself.
disconnect the horn itself and listen for the relay clicking .

Jun 12, 2009 | 1995 Jaguar XJ6

Not finding what you are looking for?
1992 Chevrolet K1500 Logo

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...