Question about 1994 Oldsmobile Ninety Eight Regency

1 Answer

It wont stay crunk unless i pour gas in that port after that it stops running

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

CAN YOU HEAR THE FUEL PUMP RUN WHEN YOU TURN THE KEY?? if so then install a pressure guage and see if the pressure drops when you try to start the car, your problem is fuel , either a pump or no voltage getting to pump

Posted on Mar 25, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Now it starts but wont stay running unless i pour gas down the intake. if i do that, it will run as long as i am pouring gas down intake, as soon as i stop it stops running. getting fuel up to throttl

Year make and model ? The injectors will open with zero pressure.
They use a magnetic valve. You should have voltage on one side and ground on the other when they are working.

Jan 15, 2014 | Cars & Trucks

1 Answer

Car will crank but will not stay crunk

check the power in your battery is ok. then check the wiring to your solenoid on top of your starter.

Dec 26, 2013 | Cars & Trucks

1 Answer

98 jeep GC limited, my jeep does not wont to stay crunk in the mornings when its cold outside i have to hold the gas down so the rpms run in 3000 till it finally keeps it self crunk. the altnator is good...

the iac ( idle air control ) needs cleaned or replaced. it controls the idling of vehicle. Also, try cleaning your throttle body. It's probably quite filthy. you can use carb cleaner to clean iac. but do not put body of iac in any liquid, just clean the valve on end. do not push it in they are preset for proper idle. have a good day !!

Mar 31, 2011 | 1999 Jeep Grand Cherokee

1 Answer

My 1987 Toyota Tercel will not run. It will start, but wont stay crunk unless im giving it gas. I check for vacuum leaks and no sucess.?

if you have a carburator then you have a blocked idle jet, simple job unscrew **** dirt out clean jet hole through, replace, (change or fit fuel filter to prevent it happening again. )
to tune is simple replace jet start motor and warm up . when at operating temp turn jet out and then in till motor runs rough then screw back out til motor smooth out , and runs sweet, if it cuts out when slowing car down (while driving) screw need to come out a slight bit more

Dec 20, 2009 | 1987 Toyota Tercel Liftback

1 Answer

My truck will not stay crunk after i replaced the starter and the alternator.

What do you mean it wont stay crunk?

If you mean it wont stay running, you probably got some wires in the wrong location, or you didnt hook up the ignition wire.

Dec 07, 2009 | 1997 Ford Ranger SuperCab

2 Answers

I filled the coolant reservoir with water & now my 1996 ford taurus wont start. Is water bad? What do I do?

water shouldn't have caused this unless motor was really hot and you poured ice water in it, I think there is another issue

Oct 03, 2009 | 1996 Ford Taurus

1 Answer

93 yukon wont stay running wont start unless u put gas in tbi?

Not sure of your question, but it sounds like a bad fuel pump or clogged fuel filter. If it stops running after gas in tbi is consumed, it is likely the fuel pump.

Dec 02, 2008 | 1998 Chevrolet K1500

1 Answer

92 ford taurus will not stay crunk if foot is not on gas

there is an idle control valve at the throttlebody usually sticks try tapping on it if the idle is ok the valve needs replacement

Nov 16, 2008 | 1989 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides