Question about 1991 Chevrolet Lumina

Open Question

How do i replace ignition coil on 1991 chevy lumina

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sledge1863
  • 149 Answers

SOURCE: 1995 lumina cranks but will not start

Sounds like it has jumped timing, dont know which engine you have so could be chain or belt.

Posted on Mar 23, 2009

Tnsiouxfalls
  • 617 Answers

SOURCE: 1990 chevy lumina apv - pickup coil -runs ok 15 mi & stalls

there's a roll pin that goes thru the drive gear.I'd change the ignition coil before the pick-up coil, if the pick up goes you'd be lucky if it would run above idle.if it has no power when it does run, try the ignition coil first.

Posted on Jul 10, 2009

  • 7 Answers

SOURCE: how do i replace the ignition coil pack on my 1995

remove the coil wires, note where they plug into. removed electrical conector. remove bolts. reverse to install. just 2 more times and your done.

Posted on Nov 16, 2009

techbuster
  • 5081 Answers

SOURCE: HOW DO YOU REPLACE A STARTER FOR 1991 CHEVY LUMINA

1) Disconnect cable from negative battery terminal
2) Raise vehicle front and suitably and safely support.
3) Remove cover from starter wiring (small right angle-like black plastic cover).
3) Loosen large wiring harness (underneath starter) so that it can be moved out of the way.
4) Remove outer nut and wires from solenoid.
5) Remove outer nut and wires wires from starter.
6) Remove two (2) screws retaining plastic flywheel cover and cover. You will need to do this - otherwise you will be unable to remove the front bolt holding the starter to the engine block. This cover is a small black plstic piece located where starter penertates the flywheel cover.
7) Remove (2) bolts retaining starter to the engine block. One is accessable towards the front of the starter/vehicile and the other (long one) is towards the rear of the vehicle - just behind the frame cross member.
8) Position starter so that if can be dropped down (flywheel gear part first).
9) Reverse the above instructions to install the new starter/solenoid

Posted on Dec 22, 2009

sienile
  • 5 Answers

SOURCE: no gas, no spark, 1991 chevy cavalier 2.2l 4cyl

This is an all too common problem with the Cavalier and other GM J-body cars. Usually it is because of the crankshaft position sensor or the harness going between it and the DIS (aka ignition module). Without the DIS seeing a signal from the crank sensor, it doesn't know when to trigger fuel and spark.

Sometimes this can also be caused by a faulty ignition switch. The switch will allow you to "crank" the car, but it doesn't make the proper connections for the ignition system, so the car never actually runs.

The previously indicated oil pressure switch could also be causing the problem, but if you hear your fuel pump run then it's OK.

Hopefully this helps. If not, your Cavalier is as messed up as mine and probably not worth fixing.

Posted on Feb 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 91 Chevy Lumina, just replaced the injectors and all the coils on saturday and ran fine but when driving it would have trouble it seemed shifting, starting today when you hit the gas the car dies...


Your ignition spark control module is going bad,your coils pack are located right underneth them. this is what tells your coils packs to produce spark to your spark plugs. they are easy to replace just make sure you mark you coil pack with some tape and make sure you put them back in the same order as they came off the spark control module. Easy to replace,just make sure you use the proper size torx or socket size on the screw heads...

May 31, 2011 | 1991 Chevrolet Lumina

1 Answer

My 1991 chevy lumina has no power when i put my foot into it and it's running rough like it wants to stall. Could this be the coil pack?


could be a few thing , have it put on a real time scanner, not a code reader, blue streak makes a good one, have someone monitor the engine activators and sensors, also hook up a furl pressure guage to monitor

May 10, 2010 | 1991 Chevrolet Lumina

1 Answer

How do you replace a fuel pump in a 1991 Chevy Lumina euro 3.1?


Had fule pump and filter replaced, 3 months later, same problem, car will not start, replaced Relay Switch, still wont work. any suggestions?

Feb 25, 2010 | 1991 Chevrolet Lumina

1 Answer

How do i replace the ignition coil pack on my 1995 chevy lumina car?


remove the coil wires, note where they plug into. removed electrical conector. remove bolts. reverse to install. just 2 more times and your done.

Nov 16, 2009 | 1995 Chevrolet Lumina

1 Answer

1991 lumina high rev


is it a 3.1v6 ? check/replace your plgs wires check/replace the egr valve

Sep 16, 2008 | 1991 Chevrolet Lumina

Not finding what you are looking for?
1991 Chevrolet Lumina Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...