Question about Chevrolet Chevy

1 Answer

I have a 1988 chevy beretta and my turn signals and brake lights are not working i checked all the fuses and they all seem to be good. what could be the problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

But make sure the hazard switch (4 ways) is completely OFF Have you been having any lighting problems for a while that you have been neglecting?
Contact me if you still Have any questions If you have a tilt wheel try moving it to another position sometimes the wires get worn because they FLEX a lot if someone always uses the tilt you can have a broke wire, the brake lights circuit runs THROUGH the turn signal switch inside the steering column.

Posted on Aug 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuel pump fuse located on 1988 chevy beretta


There are 2 Fuse Panels, one inside the Engine Compartment and one on the Drivers Side under the dash.

Nov 07, 2014 | 1988 Chevrolet Beretta

1 Answer

1988 chevy 1500 everythingworks exept brake light turn signal ok tailghts ok no brake lights


Since the turns work in the back, that means the brake bulbs are good. Brake lights and turn signal lights share the same filament in the bulb.
There is a fuse for the brake lights. Then, there is a brake light switch on the brake pedal. You need a voltmeter or test light, after checking that fuse is good. Need to check if fuse has power on it. This is one of those fuses that are hot at all times-as long as battery is connected, voltage should be going through the fuse and up to the brake light switch. Check for power both places. The switch on the pedal is a simple on-off switch. When brake is depressed, the spring loaded switch is turned on-passing power on towards the brake lights.
But then the brake wire goes into the turn signal switch before going on to the brake bulbs...however, since your turns work good, I doubt if there is a problem in the turn switch. First check if the brake light switch is sending power on when switch is on.
Let me know what you find. Good luck.

Nov 27, 2013 | 2000 Ford Focus

1 Answer

I have a 1988 Toyota truck turn signals and brake lights are not working. All fuses are good


for turn signals-check the flasher relay under dash.
for brake lights- check the switch behind the brake pedal.

Mar 21, 2013 | Cars & Trucks

1 Answer

Where do i find the turn signal flashers for a 1994 chevy beretta?


GM Corsica/Beretta 1988-1996 Repair Guide

The turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Hope helped (remember rated this help) Good luck.

Oct 30, 2009 | Chevrolet Beretta Cars & Trucks

1 Answer

Brake lights don't work on 1988 Ford Thunderbird


Check the brake light switch located under the dash, connected at the junction where the master cylinder rod connects to the brake pedal. Remove the connector and with a short piece of wire, paper clip works fine, insert into the two terminals on the connector. Check to see if your brake lights are on. If they are, your switch is bad.

Jun 27, 2009 | 1988 Ford Thunderbird

1 Answer

Checked all fuses-good, swapped bulbs-good, hazard lights-good, head lights good, turn signals-good but no brake lights. 1995 chevy silverado


Does the turn signals or hazards work in the rear?? Yes... it may be the brake switch or the turn signal switch (power goes from battery, to the brake switch then to the turn signal switch, then to the lights. No? .. again.. possibly turn signal switch or the wiring between cab and bed.

Jun 04, 2009 | 1996 Chevrolet K1500

2 Answers

No turn signals or side brake lights on 94 chevy suburban


the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Oct 18, 2008 | 1994 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...