Question about 2006 Toyota Sienna

Open Question

How do you remove the type C and D fuse (bar) from the compartment on 2006 toyota sienna? Already removed clear plastic cover and 10mm nut but still will not come out.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 2006 Toyota Sienna noisy ride

Sounds like you have an aerodynamic noise issue.

I assume that your vehicle has a roof rack.
Loosen the front cross bar, and move it backward. See if the noise "moves" backwards. If it does, remove the crossbar, it comes off from the back of the roofrack; turn it around and reinstall it.

Posted on Dec 30, 2008

  • 1 Answer

SOURCE: 2003 Toyota Sienna - Need to replace left rear brake light

Hi -
I just replaced my left rear brake light on my 2005 Sienna. I followed the manual directions and removed the two metal bolts from the tail light cover. However the assembly did not come off. I could open it a little and it appeared to be bolted from the inside. I looked online but didn't find an answer. I had already gotten pulled over and I didn't want to go to the dealer so I pulled on the assembly a little harder applying even pressure to the top and the bottom and it popped loose. I didn't yank it. There are two metal pegs that have a little lip on them and thats where you are getting the resistance. Hope this helps.

Posted on Jan 11, 2009

  • 122 Answers

SOURCE: How do you remove the starter motor in a 1999 Toyota Sienna?

this sounds correct, however, if you go to autozone.com, the have access to free online manuals, giving you step by step instructions on how to remove. you will need to register and provide some info about your vehicle. it is FREE! the manuals are in the do it your self area. Good Luck!

Posted on Sep 13, 2009

  • 1986 Answers

SOURCE: Replacing RH Side view mirror on a 2006 Toyota Sienna

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

  • 1 Answer

SOURCE: Replacing RH Side view mirror on a 2006 Toyota Sienna

I had to replace my passenger side mirror on my 2004 Sienna a while back. I took some pictures as I did it. Maybe this can help.http://time4nothing.blogspot.com/2008/03/fixing-04-sienna-passenger-side-mirror.html

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change toyota sienna 2006 valve cover gasket


Lose the engine cover,disconnect all the sensors on the valve cover,then lose all the bolt that thighten it the cylinder.
Remove the valve cover{gently} and remove the gasket nd replace it with new gasket. Apply gasket marker 2 d surface nd tight it back.

Dec 08, 2013 | 2006 Toyota Sienna

1 Answer

How do i replace gear shift light bulb in 2004 toyota sienna?


I just replaced the bulb on my 2004 Toyota Siena XLS. This is the bulb under the shifter plate in the center of the dash just above the center glove compartment. It was pretty easy once you have the process. Remove the trim on both sides of the radio in my it was the plastic wood trim. This will expose a 10mm screw on the right at the bottom of the part you just removed. You should use a panel remover tool or in my case the iPhone repair kit tool worked great. You need to turn on the ignition and move the shifter into numeral. Unscrew the shifter knob. Remove the plastic cover over the shifter with the seat heat and power adapters. This is one piece and it's held on by 4 clips. The bulb is just under the shifter panel and you turn it 1/4 of a turn to remove. The part number is 90981-11040-BULB and you will only find it at Toyota.

Nov 11, 2013 | Toyota Cars & Trucks

1 Answer

Where are the spark plugs located on a 4 cylinder 2006 toyotarav4


The spark plugs are located under the black plastic engine cover, remove the cover, there may be a couple of 10mm nuts, remove them and pull the cover off, the spark plugs are inside below each coil, each cylinder has a coil, there is no distributor, to get to the plaugs remove the electrical connector from the coils and the 10mm bolt on each then pull the coils out, you can see the spark plugs down in the holes.

Aug 21, 2011 | Toyota RAV4 Cars & Trucks

1 Answer

SPARKPLUGREPLACEMENT


The spark plugs are located under the black plastic engine cover. remove the two 10mm nuts and pull the cover off, remove the electrical connectors from each coil, remove the 10mm bolts from each coil and pull the coils out, The spark plugs are about 5 inches down in each hole you will need a 5/8" spark plug socket, a 6" extension and a ratchet wrench to take them out.

Aug 15, 2011 | 2005 Toyota Matrix

1 Answer

How do you remove a toyota tercel washer fluid reservoir


on the bottom of the front fender you will find a large black plastic cover, should have 8mm bolts holding it on, remove it, and you should be able to remove the 10mm nuts holding the tank in.

Dec 30, 2010 | 1998 Toyota Tercel

1 Answer

Remone rear wiper blade 2006 nissan murano


You need to first remove the plastic cover (it just snaps on at the base & lifts upward) that hides the 10mm nut. Remove the nut & wiggle the arm a bit to remove. then you'll need to flip the wiper blade assy until the opening in it allows removal.

good luck

Jan 26, 2010 | 2006 Nissan Murano

1 Answer

Any tools needed to change the engine air filter in a 2008 Toyota Highlander? Don't see any clips on the box...


Yes, for my 2008 3.5L Highlander, tools were required. First, make sure you get the right replacement engine air filter: there is a different part for the 3.3L and 3.5L engine. Next, as you pointed out, clips aren't used. There are two 10mm nuts that you need to loosen. They are captive (they won't fall out when you loosen them all the way). The one more in the front of the engine compartment is straightforward (once you get a 10mm socket wrench), but the one in the back is in a rather tight spot. I would suggest getting a long (6-8" shaft) 10mm nut driver. I managed to do it with a 10mm socket with a 1/4" drive and some determination. Also note that there is a wiring harness clipped to the top of a sensor adjacent to the air filter compartment; unclip it after you loosen the nuts. It works a little like a phone jack (RJ11) clip or a ethernet (RJ45) clip. Once the nuts are loose and the clip is off you lift up on the large black plastic housing marked 'see owners manual for air cleaner change' or something to that effect. (By the way my owners manual covered NONE of this.) The housing will tilt up and backwards towards the middle of the engine compartment. It won't come all the way off since it is attached to a few other things. Pull out the old filter. While it is out, you may want to wipe out the bottom of the filter compartment if you see any debris.

Note carefully that one corner is a "key"; it makes sure you install the replacement in the right orientation. Look at all four corners of the replacement part; one should look a little different. Toyota helpfully marks the replacement part with UP and FRONT. My Wix replacement had no mark whatsoever. Put the "key" corner on the corner that is more towards the front of the filter compartment and on the right side. Now put the filter cover back on. Note that one of the "hinges" goes into a socket that pops off when you remove the cover. Line that up first, then line up the rest of the cover, especially where the two captive nuts are going to go. While pushing down on the filter cover, tighten the captive nuts.

Oct 13, 2009 | 2008 Toyota Highlander

1 Answer

How do i replace the drivers side tail light on a 2006 highlander?


It was very easy. Open the back door to the highlander, remove the plastic compartment cover. You will expose the nuts and bolts that hold the asssembly to the car. Remove the nuts - be careful not to drop any inside the cavity. Once you have all the nuts removed, you can remove the lamps and pull the tail light assembly off. Put the new assembly on, replace nuts, and reinstall the lamps. Easy.

Oct 13, 2009 | 2006 Toyota Highlander

2 Answers

How do I replace the battery and where is it located?


Procedure:

Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.
Tools required:
10mm wrench, small flat screwdriver
Procedure:
Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.
Tools required:
10mm wrench, small flat screwdriver
Procedure:
Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.
Tools required:
10mm wrench, small flat screwdriver
Procedure:
Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.

Apr 17, 2009 | 2004 Nissan 350Z

1 Answer

Where is located the fuse or fuses from rear and break lights ,please. toyota sienna 98. is without rear and break lights


Remove push-on plastic nut beside parking brake. Detach side kick panel. Remove lower dash panel. Three screws, two bolts. The fuse diagram is on the back of the panel. That's for a 2000. Think it has the same body style.

Feb 18, 2009 | 2000 Toyota Sienna

Not finding what you are looking for?
2006 Toyota Sienna Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...