Question about 1997 Chevrolet Lumina

Open Question

1998 chev.s-10 2.2 lt ....what should the p.s.i. be on the fuel pump ? stalls at stops..lights...jerks & chuggs..off & on at random...is it the pump ?

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jturcotte
  • 8215 Answers

SOURCE: 1998 chev.s-10 2.2 lt codes #

Hi, you may have 2 separate problems here. 107 indicates the MAP sensor, and that may be also causing the 172 code. The other codes indicate the EGR valve position sensor, which is integral to the valve itself. I would test both of these before replacing (the EGR valve is about $150 and the MAP sensor about $60-70). First check the connectors on them for any corrosion or poor connection. The MAP sensor is mounted to the top of the intake manifold. The EGR valve is at the back of the engine near the brake booster. Please let me know if you have any questions, and thanks for using FixYa.


MAP Sensor TESTING
See Figures 1, 2 and 3 jturcotte_1442.gif

Fig. Fig. 1: Typical Manifold Absolute Pressure (MAP) sensor wiring diagram (wire color, terminal identification/location may vary on certain models)

  1. Backprobe with a high impedance voltmeter at MAP sensor terminals A and C .
  2. With the key ON and engine off, the voltmeter reading should be approximately 5.0 volts.
  3. If the voltage is not as specified, either the wiring to the MAP sensor or the VCM may be faulty. Correct any wiring or VCM faults before continuing test.
  4. Backprobe with the high impedance voltmeter at MAP sensor terminals B and A .
  5. Verify that the sensor voltage is approximately 0.5 volts with the engine not running (at sea level).
  6. Record MAP sensor voltage with the key ON and engine off.
  7. Start the vehicle.
  8. Verify that the sensor voltage is greater than 1.5 volts (above the recorded reading) at idle.
  9. Verify that the sensor voltage increases to approximately 4.5. volts (above the recorded reading) at Wide Open Throttle (WOT).
  10. If the sensor voltage is as specified, the sensor is functioning properly.
  11. If the sensor voltage is not as specified, check the sensor and the sensor vacuum source for a leak or a restriction. If no leaks or restrictions are found, the sensor may be defective and should be replaced.

jturcotte_397.jpg

Fig. Fig. 2: Using jumper wires and a high impedance voltmeter test between MAP sensor terminals A and C with the key ON and engine off. The voltage should be approximately 5 volts

jturcotte_398.jpg

Fig. Fig. 3: Next test between MAP sensor terminals A and B with the key ON and engine off. The voltage should be approximately 0.5 volts



EGR test: requires a GM scan tool:


jturcotte_1443.gif



EGR replacement:

Linear EGR Valve

  1. Disconnect the negative battery cable.

Note the position of the EGR valve prior to removal. Do not rotate the valve 180?.
  1. Unplug the valve electrical connection..
  2. Unfasten the valve retainers, then remove the valve and the gasket.

To install:

  1. Clean all gasket residue from the gasket mating surfaces.
  2. Install a new gasket and the valve.
  3. Install the valve retainers.
  4. On 1998-99 2.2L models, tighten the retainers to 19 ft. lbs. (26 Nm).
  5. Attach the valve electrical connections and connect the negative battery cable.

Component locations:

jturcotte_1444.gif

EGR valve wiring:


jturcotte_1445.gif
EGR valve pic;

jturcotte_401.jpg

MAP sensor pic:

jturcotte_400.jpg

Posted on Apr 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 chev actro van starts then stalls


Get a fuel pressure gauge and make sure you have constant fuel pressure. should be arround 30 lbs id double check with your local parts store. If you dont maintain good pressure your fuel pump could be failing.v

Nov 07, 2013 | Cars & Trucks

2 Answers

1999 buick century stalls and chuggs at random


Try first to replace the fuel filter. Then if that don't work, have the sensors checked by an auto technician with a diagnostic tool that interfaces with the cars computer. Most places will do this for free.

Sep 28, 2012 | 1999 Buick Century

2 Answers

Evap code showin on my 1998 hyundai accent sohc. any tips for trouble shooting??? >>>>clueless<<<<


Not until you share the code with us

Your going to need a repair shop

Are you familiar with EVAP System
components

You won't have the smoke machine
or scanner to do anything

Mar 19, 2011 | Hyundai Accent Cars & Trucks

1 Answer

Van jerks sometimes while driving and dies sometimes when stopped


first thing to do is clean the throttle body. it will probably cure the stall and **** problem

Apr 16, 2010 | 1994 Plymouth Voyager

1 Answer

Engine runs extremely rough, seems to be fuel related, new fuel pump & filter installed, pressure good, run 2 bottles of injector cleaner through. Can't get to stay running under load. 1998, chev....


Have you changed the plugs, if any are fouled out or if any are worn, it takes more to fire it under load and may be spark knocking because one of the plugs can't fire off all the gas and cause it to skip or idle rough.

Jan 18, 2010 | 1998 Chevrolet K1500

1 Answer

I am having the same problems with 2003 Kia Sedona


Drop the fuel tank and replace the fuel pump. Filter is attached to the fuel pump. Sounds like the fuel pump is failing.

Jul 02, 2009 | 2003 Kia Sedona

2 Answers

1998 GMC Jimmy, bogged down, stalled and won't sart back up


does it have spark? you did verify fuel pump working properly? could it have a clogged converter? is the engine lite on?

Nov 16, 2008 | 1998 GMC Jimmy

Not finding what you are looking for?
1997 Chevrolet Lumina Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...