Question about 1999 Suzuki Vitara

1 Answer

99 vitara need to instal a cam shaft censor got a new one need to know how to instal it

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 90 Answers

Just dis-connect the electrical plug and unscrew the old sensor. Once out, screw the new sensor in and connect the plug. If the new sensor doesn't have an o-ring on it near the thread it'd be a good idea to put some thread tape on it to make sure oil doesn't leak out. To remove the old sensor and intall the new one there's actually a specially socket you can buy that has a slot in it for the wires. It can also be done with a spanner but the sensors can sometimes be very tight. Be careful not to let the spanner slip as it may round off the nut or even cause personal injury.

Posted on Mar 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Nissan Altima crank shaft censor located bank 2


there is only one crankshaft sensor so you will be looking for a CAM shaft sensor for it to be on bank 2
go google and type in --location of cam shaft sensors on nissan altima engine ---

Dec 18, 2016 | Nissan Cars & Trucks

1 Answer

Running ruff need to replace cam censor could you tell where to locate it


How do you know if any parts are needed?

What OBD Codes did you have?

Who component tested a system, to find a fault
& failed part?

Surely your not going to throw parts at the unknown !!

You can google your locations,install your parts & still have the
same problem,good luck with that

Aug 26, 2014 | 2001 Chevrolet Chevrolet Blazer

1 Answer

Where is the cam shaft sensor located on a 2001 suzuki grand vitara


which engine,????
but is on the end of one cam shaft
the 2.0 liter and 2.5 is left rear cam.
RTM?
https://suzukipitstopplus.com/Products/1191-2001-vitara-grand-vitara-service-manual.aspx

here is mine, first learn what engine you have, a car body tells me nada
2L
http://www.fixkick.com/engine/20Liter/20L-PARTSFINDER1.pdf

2.5L
http://www.fixkick.com/engine/2.5L%202004%20Tracker/25L-2004-engine.pdf

see em?

or is this G16?
on the G16 the CMP is in the base of the distributor.

aka, CMP or CAS, cam angle sensor. but is on end of cam.
on DOHC engines and V6s/

Jul 06, 2014 | 2001 Suzuki Vitara

1 Answer

I have 2 engine codes on my 2005 dodge neon. they are p0325 and p0340. the car has problem starting and misses badly for a while. What is the problem and how do i fix it? thanx for the help!


the p0325 code pertains to a knock censor. the p0340 is for your cam shaft sensor. i've had this problem before. try replacing the cam shaft censor first and run the codes again to see if the other still comes up. it should fix the problem. hope this helps

Jun 24, 2014 | 2005 Dodge Neon SXT

1 Answer

Misfire on 2 and 5


Hi Paula,

You didn't mention if you changed the plug wires.

You mentioned replacing the camshaft sensor. Have you checked the Crankshaft Position Sensor? Or the Mass Air Flow Sensor (may need cleaning)? Or the Throttle Position Sensor?

Jan 11, 2014 | 2000 Jeep Cherokee

1 Answer

Replace seal on drive shaft


if you have a 99 Suzuki vitara 2.0 it came with a 2 piece drive shaft that is hard to find. it has a center piece that hold it together. I had my drive shaft made into a 1 piece---it's doing find

Apr 02, 2013 | 1999 Suzuki Vitara

1 Answer

Can you explain how to replace a cam shaft censor on my 300m 99


Welcome to FIxYa.com


The camshaft position sensor is installed in the timing belt housing cover above the left camshaft sprocket.

Removal:

1. Disconnect the negative battery cable.

2. Remove the upper intake plenum.

3. Disconnect electrical connector from sensor.

4. Remove camshaft position sensor bolt.

5. Pull sensor up out of the timing belt housing.



Installation:

If the removed sensor is reinstalled, remove the old spacer from the sensor face, Attach a

new spacer to the face of the sensor.



If installing a new sensor be sure that the paper spacer is attached to the face.

1. Install sensor in the timing belt housing and push down until contact is made with the camshaft sprocket. While holding down in position, install and tighten bolt to 12 N.m(105in.lbs) torque.

Hook up electrical connector.

Connect Negative battery back up.

leedavidian_13.png


Regards, Lee Davidian


Thank you for using FixYa.com

Nov 05, 2010 | 1999 Chrysler 300M

1 Answer

Cam shaft censor


shud always get 2 or 3 scans for more opinionsor ask parts place guys for tips--never just replace parts in a hurry--inspec auto for loose vacuum hoses-wires...Is the batt cables tite at the post--not every solution comes on computer--get haynes manual at discount place-its a pros book

Apr 22, 2010 | 2004 Chrysler 300M

1 Answer

Cranks but wont turn over


you know. i took it to a mechanic and actually.... The timing belt cut the Crank Shaft Censor... So it was the crank shaft censor again. The wires were routed wrong from the first mechanic that "fixed" the car.

Aug 01, 2008 | 2000 Hyundai Sonata

Not finding what you are looking for?
1999 Suzuki Vitara Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...