Question about 1997 Ford Probe

1 Answer

Need to replace ignition cylinder. no keys - 1997 Ford Probe

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal

  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    need to replace ignition cylinder. - j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Posted on Mar 25, 2011

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 323 Answers

SOURCE: '97 Sebring Convertible Replace Ignition lock cylinder w/o key

Go to the dealer with the VIN and they can cut a new key to fit the original cylinder.

Posted on Sep 05, 2009

jmgldsmth
  • 1889 Answers

SOURCE: Removal of 1998 toyota cressida ignition key cylinder.

This car has drillable shear pin screws on the bottom of the lock yoke you must drill these out.
then release the clip to the cylinder. you must get a new set of break-off shear pin head screws from the dealer to finish the job.

Posted on May 19, 2009

emissionwiz
  • 76846 Answers

SOURCE: Recoding "spare" key for car after ignition cylinder was replaced

Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing working key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

Posted on May 12, 2009

  • 85 Answers

SOURCE: how to replace a ignition lock cylinder for a 1999

youve been passlok screwed// patience and a lot of coffee its hard to explain this thing but with some staring and thought its not that hard also type in relearn procedure for this car in your browser make sure you typ every thing about it

Posted on Feb 27, 2010

joshnaz
  • 186 Answers

SOURCE: key ignition switch needs replaced lock cylinder

disconnect the battery and pull the air bag fuse out to diable the air bag. Remove the steering coulmb trim covers and expose the lock cylinder. If the lock cylinder can be turned and is functional then push in the bottom tab and turn the lock cylinder then pull the whole cylinder out. If the keys broke inside and the lock cylinder is not functional the bottom tab will need to be drilled out.
graphic.aspx?mod=reptiff&module_id=1&session_id=%7b812b1a44-e9f7-498d-9233-3843c35aa6d4%7d&image_guid=00010135&print_bw=0&

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Lost key for 1999 Chrysler Cirris.need to replace ignition lock cylinder


take center of steering wheel off,access the star screw through a hole in the wheel to remove mechanism

Jul 23, 2015 | Chrysler Cars & Trucks

2 Answers

Replace ignition cylinder


The key has to be in the switch, battery unhooked, turn key to start position, insert probe into small hole above cylinder to trip the wedge, and pull out.

Aug 19, 2012 | 2001 Chevrolet Silverado 1500

1 Answer

Replaced old ignition with new one and the new ignition won't lock in place


If the ignition wont lock in place,just redo it but this time you need to realize that you install the key cylinder with the key in the ON postion,straight into the lock cylinder housing,aligning the retaining tabs,on the key cylinder with the hole in the lock cylinder housing.Then turn the key to the off position,

Aug 07, 2012 | 1997 Plymouth Grand Voyager

2 Answers

Can't put key into ignition


Hello: It sounds like the tumblers came loose in the ignition lock cylinder. You will need to replace the lock cylinder and possibly the key to. A worn key is hard on the lock cylinder.

Jun 07, 2011 | 2002 Cadillac Deville

2 Answers

Key wont turn on 2004 Alero. If key is inserted and door is opened the alert bell sounds off indicating keys have been left in ignition,but that is all that is functioning. Have tried 2 different keys and...


Ignition lock cylinders are pretty notorious for this. You may get the thing to turn by wiggling the key up and down while turning at the same time. I have also had luck in tapping on the cylinder with a screwdriver handle while turning the key. To completely fix the problem, you will have to replace the lock cylinder. GM (AC Delco) lock cylinder kits come with an assortment of tumblers so the new cylinder can be set-up to work with your existing keys.

Jan 29, 2011 | 2004 Oldsmobile Alero

1 Answer

Ignition switch would start but would not lock into position (RUN) and would shut off and then ignition completely locked down and will not move


The ignition key cylinder in a Buick unlocks the ignition and allows the Buick's engine to start. The cylinder contains a switch on the end of it (inside the cylinder) that sends an electric signal to the starter motor. When the ignition key cylinder fails, the Buick won't start. When this happens, you'll need a new ignition cylinder. Purchase replacement cylinders from Buick.
Difficulty: Moderately Easy
Things You'll Need:

  • Ignition key
  • Punch pin
  • Cross-point screwdriver
  1. 1 Remove the screws on the bottom of the steering column on your Buick. These screws hold the steering column cover on. You may need to tilt the steering wheel to its highest position to access these screws.
  2. 2 Turn the ignition key to the "II" position in the ignition cylinder.
  3. 3 Slide the punch pin into the access slot on the bottom of the ignition cylinder.
  4. 4 Push the pin all the way into the access slot while you pull the ignition cylinder out of the steering column.
  5. 5 Insert the new ignition cylinder into the steering column with the key in the "II" position on the cylinder.
  6. 6 Push the cylinder into the column until it "clicks," indicating that it is locked into the column.
  7. 7 Turn the ignition key to the "Off" position.

Dec 15, 2010 | 1995 Buick Riviera

1 Answer

Ignition key doesn't return to full off position, and prevents key removal.


GM had problems with both the ignition cylinder and the transmission shifter on these vehicles. The original ignition cylinders are going to fail, it's just a matter of when they do it, and many people have had problems with the shifter also. Odds are it's the ignition cylinder, you could check by disconnecting the shift cable on top of the transmission, then see if the ignition cylinder will then turn off. If it does, the shifter will need replaced, if not, you'll need to replace the ignition cylinder.

Jan 24, 2010 | 2003 Chevrolet Malibu

1 Answer

How do you change a key switch in a 2001 chevy impala, the factory keys wont turn in the switch


If your key is worn try getting a new one cut.
The ignition lock cylinder and keys do not contain any coded electronic components. The lock cylinder housing contains the coded electronic components. Changing an ignition lock cylinder or replacing a key is a purely mechanical process which does not affect the vehicle theft deterrent system. To replace an existing key, simply cut a new key to match the existing one. If no keys are available, the lock cylinder must be changed. To change the lock cylinder, simply replace the existing lock cylinder with one of the same type.
If you are unable to operate the ignition cylinder with a new key then you will probably need to replace the cylinder and switch.Replacement of the switch involves reprogramming
The system may be programmed with or without a scan tool.
There is a way to get the cylinder out without replacing the switch but this procedure should be performed by a qualified GM technician as it involves removal of the switch and some precise drilling.

Nov 01, 2009 | 2001 Chevrolet Impala

1 Answer

2000 contour


for 98 contour issue. TSB 98-21-14 not covered by warranty

This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar)

Mar 09, 2009 | 2000 Ford Contour

1 Answer

1997 ford contour


this is for 98, but may apply if yours is late 97 build.

Article No.
98-21-14
  • IGNITION SWITCH - HIGH EFFORT IGNITION KEY INSERTION/REMOVAL AND/OR KEY CHIMES SOUND WITH DOOR OPEN AND IGNITION KEY REMOVED
Publication Date: OCTOBER 15, 1998
FORD: 1998 CONTOUR LINCOLN-MERCURY: 1998 MYSTIQUE
1999 COUGAR
This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar

Aug 13, 2008 | 1997 Ford Contour

Not finding what you are looking for?
1997 Ford Probe Logo

1,353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...