Question about 2003 Chrysler PT Cruiser

1 Answer

My 2003 Pt Cruiser skips when under pressure going uphill only.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Contributor
  • 299 Answers

HOW MANY MILES ON CAR.

Posted on Mar 25, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My pt cruiser has code 1391. i changed cam sensor crank sensor wires plugs and coil still getting 1391 code and from 0 mph to 20 mph car skips and revs up any ideas?


The cam and crank sensors have the same power wire. Go after that one. They also have the same ground, but other sensors connect to it also. So it's not the ground. And they have separate return signal wires. Not them either.

Mar 09, 2015 | 2001 Chrysler PT Cruiser

1 Answer

Wher can i get a wiring diagram of starter circuit on a 2003 pt cruiser?


At a local repair shop --off their data base

Free --from auto zone site, so i here,don't know
how that works

Jul 17, 2014 | 2003 Chrysler PT Cruiser

1 Answer

Roaring in front when going down highway


this vehicle has thermostatic fan when engine gets hot enough under load ie, going uphill it will engage and you will hear a roarining sound which during normal driving you probably wont notice, once the engine cools down the sound will go away.

hope this helps art

Jun 12, 2012 | 2004 Chrysler PT Cruiser

1 Answer

2003 PT Cruiser turbo. Has just 67k miles on it. Just began making a low pitched loud whistle sound on acceleration or load/uphill. Gets louder with greater acceleration/load, no decrease in power.


I took my car to Keller's Auto Repair in Gettysburg PA, He specializes in Chryslers. I have 04 Cruiser with 2.4 Turbo that had the same whistle noise, and check engine light on. He found code P0301. The noise was caused by the #1 Cylinder injector O ring. Check them out on facebook. They will help you.

http://www.facebook.com/#!/pages/Kellers-Auto-Repair/158207620880499

Sep 24, 2010 | 2003 Chrysler PT Cruiser

2 Answers

2005 Pt Cruiser idles rough at stop lights/ poor gas mileage.


i hav a 2003 pt cruiser 2.2 crd touring it wont go over 3000 revs engine light cums on. error code p0243 i hav replaced wastegate solenoids cleaned egr valve cud it be the mass air flow sensor that has a problem thanx

Sep 18, 2009 | 2005 Chrysler PT Cruiser

2 Answers

Check engine light on and code po108


PO108 (map circuit high input) MAP is manifold absolute pressure... a sensor normally mounted on the intake. your code is suggesting a problem with this sensor, or its circuitry.

May 11, 2009 | 2003 Chrysler PT Cruiser

2 Answers

Where is the power steering sensor located on a pt cruiser


i have changed the pressure sensor switch on my 2001 PT Cruiser (B). to find it you will have to put the car on ramps and go under the car until your under the cross member (right behind the front wheel) it will be just behind the cross member closer to the driver side wheel. remember once you remove the sensor gravity will work against you and power steering fluid will pour out of the sensor hole. and when under a car there is really no place to go and if your not careful you will have to resign yourself to being covered in fluid. good luck!

Apr 13, 2009 | 2001 Chrysler PT Cruiser

1 Answer

My 2003 pt cruiser keeps losing tire pressure..took back to the dealer twice and they said they did somethig to the rims because they were rusting but does not seem to hold pressure even with nitro in the...


your rims are too badly rusted to get a good seal between the tire and rims.  You need to replace the defective rims.  This is a good time to buy some fancy rims or used ones from a junk yard. 

Mar 26, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
2003 Chrysler PT Cruiser Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...