Question about Dodge Caravan

1 Answer

Runs on high only? - Caravan Dodge Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 8,195 Answers

Hi, if your talking about the blower motor, this is caused by a failed resistor.

Please see my tip at http://www.fixya.com/cars/r6234839-doesn_t_heater_or_air_conditioner_blow . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Posted on Mar 25, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my name is Larry I have a 1998 Pontiac sunfire & my problem that I have is I have low beam. But no high beam.


It's probably the switch , but testing to know for sure is alwasy a good idea .

Headlamps Inoperative - High Beams
Step
Action
Value(s)
Yes
No
1
Did you perform the Daytime Running Lamps (DRL) System Check?
--
YES - Go to Step 2
NO - Go to Daytime Running Lights (DRL) System Check
2
Disconnect the turn/hazard headlamp switch connector C1.
Connect a fused jumper between terminal B of the turn/hazard headlamp switch assembly harness connector C1 and ground.
Do the high beam headlamps operate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the turn/hazard headlamp switch assembly.
Did you complete the repair?
--
Go to Daytime Running Lights (DRL) System Check
--
4
Repair the open in CKT 1200 between the turn/hazard headlamp switch assembly. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?

Daytime Running Lights (DRL) System Check
Step
Action
Normal Result(s)
Abnormal Result(s)*
1
Turn the headlamp switch to the HEAD position.
Turn the headlamp dimmer switch to the LOW position.
The low beam headlamps are ON.
The high beam headlamps are OFF.
Headlamps Inoperative - Low Beams
2
Turn the headlamp switch to the HIGH position.
The high beam headlamps are ON.
The high beam indicator is ON.
The low beam headlamps are OFF.
Headlamps Inoperative - High Beams
3
Turn the headlamp switch OFF.
Turn the ignition to ON.
Disengage the parking brake.
The high beam headlamps come ON at a reduced intensity in approximately 30 seconds.
Daytime Running Lamps (DRL) Inoperative, Headlamp Switch Operates Normally
* Refer to the appropriate symptom diagnostic table for the applicable abnormal result.

Jan 13, 2017 | 1998 Pontiac Sunfire

1 Answer

Cooling fan motor gets hot when running high speed why


Check the bearings. If the friction is high the fan will not run at rated speed. When it runs slower it uses more current and gets hotter...

Disassemble, clean and lubricate to make sure fan runs full blast and does not burn out.

Or if the fan has two windings, one for starting and one for running it is possible that the high speed run winding has some shorts in it resulting in more current and more heat.

Oct 13, 2015 | Cars & Trucks

1 Answer

2003 Silverado oil pressure running high what is cause it


Possibly oil too high a viscosity or sender is faulty.

Oct 18, 2014 | Cars & Trucks

1 Answer

2002 Dodge Caravan headlamps: one works on dim the other works on high beam but not together. Also only one daytime running lamp.


Your van has dual diligent headlamp bulbs, that means each headlight has one bulb that serves as high beam and low beam. What has most likely happened is on one side the low beam filament has burnt out, and on the other side the high beam filiment has burnt out. The daytime running lights are just the high beam filament running on reduced power, so if the high beam doesn't work on one side, that same side will have no daytime running light. Replace both headlamp bulbs with matching, good quality bulbs.

Mar 06, 2011 | 2002 Dodge Grand Caravan

1 Answer

High beam headlight does not work properly


it more then likey a lose wire or bear one. run the line down. i think that the high beams run on diff. fuses. you can try that!

Jul 13, 2009 | Infiniti G35 Cars & Trucks

1 Answer

I have a 1994 es 300 and my car keeps running hot when the AC is on. It only runs hot when im in town, when im on the highway or in the country it doesnt. my dad replace everything just about! and it still...


turn on ac and see if fans come on ,,see if fans or fan kicks into high after a little while ,look for reason why fans or fans do not run with ac on they have to run ,relay? or high side switch check preasures on ac ,low side and high,high side may be to high for fans or fan to cool down ,,ac problem or to much freon,,,radiator new?

Jul 03, 2009 | 1995 Lexus ES 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...