Question about 1999 Oldsmobile Alero

1 Answer

What is torque for flywheel or flexwheel for 99 olds alero with a 2.4?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Oldsmobile Master
  • 14,036 Answers


Posted on Mar 25, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The flywheel bolt wont line up to where i can get the torque conveter bolts in

Make sure the torque converter is in all the way. It should spin freely and be about 1/2 - 1/4 inch away. You can either put a big socket on the bolt in the front of the harmonic balancer and turn the engine to where you can easily access the flywheel holes. Then while spinning the torque converter push in into the transmission. You may have to try to get a pry bar up in near the center of the torque converter to push it straight in (while spinning it). If not, you will either have to separate it again (take out the two side lower bolts first and insert some LONG ones of the same thread to give you room and keep it lined up) and remove the other 4 bolts completely. If you're sure it's in all the way. Either the torque converter or flywheel may be wrong. If you have a 4L60E and someone gave you a '98 or '00 there could be a problem as the '99 is supposed to be '99 only. Some people say otherwise. However it's been my experience that the '99 Astro/Safari/s10/s15 4 WD and AWD will work fine but other years sometimes have the peanut (small) converter. Or someone may have assumed that the 4L60E was the same from a full sized GM 4x4 product. I hope that helps. If so please leave a testimonial and rate my assistance. Thanks for using Fixya.

Feb 20, 2011 | 1999 Chevrolet Blazer

2 Answers

Torque spec on 99 olds alaro 3.4 head bolts


Aug 16, 2010 | 1999 Oldsmobile Alero

1 Answer

What is the torque per pound or per in for the

If you are embarking on DIY car care, I highly recommend buying a service manual. You can find them on line from Haynes, eBay, and often as loaners at larger public libraries.
'99 Alero (also covers a number of other related vehicles.)
You'll find complete torque specs, electrical diagrams and many tips.

Jun 28, 2010 | 1999 Oldsmobile Alero

1 Answer

Cyl head torque renault clio 1.4 1998

Its very very complicated - Ach! the french!!! ---- Stage 1 torque to 20nm ----------- Stage 2 - wait 3 minutes.---------- Stage 3 - fully slacken all bolts in sequence------- Stage 4 - torque to 20nm-------- Stage 5 - tighten by 97 degrees (plus or minus 2 degrees - so 95-99 degrees really)--------
Tightening sequence, with the flywheel on the right looking down on engine - top row of bolts are 1,2,3,4,5 -------- bottom row of bolts are 6,7,8,9,10 --------- sequence is, 8,3,4,9,7,2,5,10,6,1----

Dec 08, 2009 | 2007 Chevrolet Impala LS Sedan New Cars

2 Answers

How to set timing on a 99 olds mobile alero?

If you are going to do a timing belt job you should get a book. Along with timing you will need to torque specs. Most parts stores sell manuals for $20.

Oct 26, 2009 | 1999 Oldsmobile Alero

2 Answers

1999 olds alero where is my fuel filter

The fuel filter is located under the car right in front of the fuel tank.You need to have up on jackstands to get to the filter.
Mine is located BEHIND the gas tank, between the tank and the rear (axel) support ('99 Olds Alero 3.4l v6 2 door coupe)

Oct 21, 2009 | 1999 Oldsmobile Alero

1 Answer

License plate bulb 99 alero

remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the should pull straight out

Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

2 Answers


intake manifold has a vacum leak or other vacum leak hose etc.

Dec 03, 2008 | 1999 Oldsmobile Alero

Not finding what you are looking for?
1999 Oldsmobile Alero Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides