Question about Ford F-150

1 Answer

Egr failed to open, replace with a new EGR Valve and solinoid light is still on .How can i reset the code?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,039 Answers

Simply disconnect the battery for 1 minute computer will reset code thanks pierre

Posted on Aug 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wont pass smog , check engine light is on . It is setting off code 1406


CODE P1406 - EGR VALVE PINTLE POSITION CIRCUIT MALFUNCTION CONDITIONS. POSSIBLE CAUSES EGR SOLENOID VALVE IS BINDING OR STICKING. EGR SOLENOID CONTROL CIRCUIT IS OPEN SHORTED TO GROUND OR TO B+. EGR SOLENOID POWER CIRCUIT IS OPEN CHECK THE ECS 10AMP FUSE.EGR SOLENOID FAILED. PCM HAS FAILED.

Aug 13, 2011 | 1997 Cadillac Eldorado

2 Answers

1999 mercury sable engine code p1744,p0401. Failed e check. EGR looks new, replaced egr solenoid then cleared codes. what more can i do about the p0401 code and the p1744 code Thanks


for p0401:
In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open.
Clean out the EGR valve and/or tubing to remove deposits.
Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model).
Replace the DPFE sensor (with a good quality / OEM one).
Replace the EGR valve.

Jul 08, 2011 | 1999 Mercury Sable

1 Answer

Trouble code P1406 Failed EGR value, Open or short circuit condition Also code P0301 misfire cylinder 1 Next steps? Information for replacing EGR value? 1997 Bonneville SE 105K


P1406 Code - EGR Valve Pintle Position Circuit
The PCM monitors the EGR valve pintle position input to ensure that the valve responds properly to commands from the PCM and to detect a malfunction if the pintle position sensor and control circuits are open or shorted. If the PCM detects a pintle position signal voltage outside the normal range of the pintle position sensor, or a signal voltage that is not within a tolerance considered acceptable for proper EGR system operation, the PCM will set DTC P1406.

CONDITIONS FOR SETTING THE DTC

Ignition 1 voltage is greater than 10 volts.
EGR Feedback is less than 0.14 volt at any time.

OR

EGR Feedback is 0.4 volt greater or less than the EGR Closed Valve Pintle Position when the Desired EGR Position is commanded to 0%.

OR

Actual EGR Position is 20% greater or less than the Desired EGR Position.
Any of the above conditions are present for longer than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS

The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data.

CONDITIONS FOR CLEARING THE MIL/DTC

The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed.
The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
The DTC can be cleared by using the scan tool Clear Info function or by disconnecting the PCM battery feed.

DIAGNOSTIC AIDS
Check for the following conditions:

Open EGR ignition filter circuit.

An open in the EGR ignition filter circuit will cause EGR Position Error to vary erratically while the EGR valve is operating. With the ignition ON, a test light should illuminate when connected between ground and the EGR ignition filter circuit at the PCM connector. If not, locate and repair the open in the EGR ignition filter circuit.

Excessive deposits on EGR valve pintle or seat.

Remove the EGR valve and check for deposits that may interfere with the EGR valve pintle extending completely or cause the pintle to stick.

Poor connection or damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, observe the Actual EGR position display on the scan tool while moving connectors and wiring harnesses related to the EGR valve. A change in the display will indicate the location of the malfunction.

Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table:

Verifies that the malfunction is present.

The PCM contains a recirculation diode which filters the EGR ignition feed for the EGR valve. The recirculation diode is connected to the ignition filter (EGR ignition feed) circuit. If the ignition filter circuit is open, Actual EGR position may be erratic when compared to Desired EGR position. An open in the EGR ignition filter circuit will cause DTC P1406 to be set after an extended period of time.
If DTC P1406 will only set under certain conditions, the malfunction may be intermittent; refer to DTC P1406 Diagnostic Aids. If an intermittent wiring problem is not present, check for a poor connection at the PCM or the EGR valve. If the connections are OK and DTC P1406 continues to set, replace the EGR valve.

This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.


------------------------------------------------------------------------------------------------------------------------------
P0301 Code - Cylinder #1 Misfire Detected
A P0301 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #1.

Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present

Causes: A code P0301 may mean that one or more of the following has happened:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer

Possible Solutions:
If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.

If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.


Check it and keep us updated.

May 03, 2011 | 1997 Pontiac Bonneville

4 Answers

Insufficient egr flow, already replaced egr valve and purge valve canister


I too replaced the egr valve and was discouraged that the check engine light came back on with the same "insufficient flow" code. I took it to my mechanic to put it on the monster diagnostic machine. It said "check all vacuum line, and or map sensor". After looking real close we found a melted vacuum tube, and a cracked vacuum angle connector. Replaced both vacuum pieces, reset the codes, and good to go. If that fails than the next thing is the map sensor, that tells the EGR valve what to do.

Jan 12, 2010 | 2002 Chevrolet Impala

1 Answer

My engine light came on. The code reading machine


might just need to reset the computor unplug battery for 5 min that should do it

Nov 16, 2009 | 1999 Toyota Celica

1 Answer

Failed e check


just replace the egr solinoid

May 23, 2009 | 1998 Mercury Villager

1 Answer

Egr code still present after changing solinoid and checking valve


Have you had the code reset using an OBD 1 scan tool? It must be reset as the code remains in the computer.

May 03, 2009 | 1999 Ford Taurus

1 Answer

WONT PASS INSPECTION ... 2ND SYSTEM ON EGRSYSTEM FAILED is that my egr vavle?


sounds like the solinoid but if the egr has a wiring clip on top of it its 1 piece if u price it prob 200 bucks or more i would first unbolt it and clean the valve with carb cleaner while pushing valve back and forth w/ screw driver then put back and drive to turn off light or disconnect batt to reset code then get it inspected cause if that works may not last but at least u know the problem

Mar 26, 2009 | 1999 Chevrolet Silverado 1500

3 Answers

1992 saturn coupe 4 cyl motor twin cam


that code is your egr valve or your egr solenoid.sometimes you can remove valve and clean thoroughly with brake cleaner for a cherap alternative.

Sep 22, 2008 | 1992 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...