Question about 1995 Honda Accord

1 Answer

Is a engine crankshaft pulley easy to fix on your own

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 130 Answers

Not really..it requires special tools to pull the pulley off the motor and its just as difficult getting a new one back on....most likely it would also require removing other parts to be able to get to that point... however, most "shadetree" mechanics can do this if they have the tools and there is really nothing they can mess up.. if you take it to a shop, Im guessing it would be $300-$400 labor depending on whre you are

Posted on Mar 25, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the crankshaft dumper pully?


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

Jan 27, 2016 | 2006 Land Rover Range Rover Sport

1 Answer

How to fit strechy fan belt on ford focus 2006 model


It depends on what engine it has. On the 1.4/1.6 petrol engines a universal stretch belt tool will do it, the problem comes if it's got a separate belt for aircon as the crankshaft pulley has two sets of v grooves and it's difficult to force the larger inner belt over the crankshaft pulley as it keeps slipping off the water pump drive.
There is a special tool that fits to the water pump pulley that makes fitting easy but it is possible to do it without it by using a lever between the chassis rail and the water pump to stop the belt coming off the side radius of the pulley. The aircon belt is easy using the universal fitting tool. It is possible to use brute force with screwdrivers but will normally damage the belts and a cheap fitting tool can be brought to actually save money and aggro !

Apr 22, 2012 | Cars & Trucks

1 Answer

1997 acura tl crankshaft spinning freely, is this normal? Just replaced a/c compressor and the pulley is turning real slow. Belt is not slipping. The crankshaft pulley and a/c pulley/belt rotate normally...


CHECK SEE IF CRANK SHAFT PULLEY BOLTS LOOSE.IF CRANKSHAFT PULLEY LONG BOLT TORQUE IS FOR 130 FT LBS FOR 1.8L ENGINE. IF YOU HAVE THESE ENGINES CRANKSHAFT BOLT TORQUE IS 174 - 181 FT LBS ENGINES ARE 3.0L 3.2L 3.5L 2.3L 2.5L IF CRANKSHAFT PULLEY BOLT IS TIGHT.THE CRANKSHAFT PULLEY ITSELF BROKEN NEED REPLACING.

Sep 05, 2011 | 1997 Acura TL Series

3 Answers

I would like to know where the crankshaft gasket is? I have a 1994 dodge spirit, a 6 cyl. How hard is it for me to replace the gasket?


3.3L and 3.8L Engines
  1. Raise and safely support the front of the vehicle on jackstands.
  2. Remove the right front wheel and inner splash shield.
  3. Remove the accessory drive belt from the engine.
  4. Remove the center bolt of the crankshaft pulley.
  5. Using a claw-type gear puller, remove the crankshaft pulley from the crankshaft. When using the puller, make certain that the claws are situated on the inner section of the pulley. If the claws are used on the outer section of the pulley, the pulley will be damaged.
  6. Use tool C-4991 or the equivalent to remove the oil seal from the timing chain cover. Make certain not to damage the crankshaft seal surface of the cover. Fig. 10: Use a claw-type gear puller to remove the crankshaft pulley/damper — 3.3L and 3.8L engines 86723231.gif
    Fig. 11: Use the seal remover tool C-4991 to remove the crankshaft oil seal — 3.3L and 3.8L engines 86723230.gif
    To install:
  7. Install the new seal by using tool C-4992 or the equivalent. Place the seal into the opening with the seal spring towards the inside of the engine. Install the seal until flush with the cover.
  8. To install the crankshaft pulley to the crankshaft a 5.9 in. (150mm) long bolt, a thrust bearing and washer, and plate L-4524 or equivalent.
    1. Tap the crankshaft pulley onto the crankshaft with a rubber or plastic mallet making sure to hit the pulley on the center portion.
    2. Once the pulley is started onto the crankshaft, install a nut the thrust bearing and washer, and the plate L-4524 onto the bolt.
    3. Thread the bolt into the end of the crankshaft and screw it in at least 2 or 3 complete turns.
    4. Tighten down on the nut on the bolt to slowly press the pulley onto the crankshaft until completely seated.
    5. Remove the bolt, nut, washer and thrust bearing, and plate L-4524 from the crankshaft. Fig. 12: Installing the crankshaft pulley — 3.3L and 3.8L engines 86723229.gif

  9. Install the center crankshaft pulley bolt and tighten it to 40 ft. lbs. (54 Nm).
  10. Install the accessory drive belt and tighten by following the instructions in Section 1.
  11. Install the splash shield and front wheel.
  12. Lower the vehicle to the ground.

Jul 16, 2010 | 1994 Dodge Spirit

1 Answer

Would like information on timing belt settings on a 1993 Isuzu Rodeo 4X4 3.2 We have already bought the book. It seems that the setting still are not what this particular motor/engine needs are there other...


look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)


  1. Pusher
    • Tighten bolt to the specified torque.
Torque 19 N-m (19 lb-ft)


  1. Timing belt cover
    • Remove crankshaft pulley that was installed in step 9.
    • Tighten bolts to the specified torque.
Torque 17 N-m (12 lb-ft)


  1. Oil cooler hose
    • Tighten oil cooler hose bracket bolts to the specified torque.
Torque 22 N-m (16 lb-ft)


  1. Crankshaft pulley assembly
    • Using special tool J-8614-01, hold the crankshaft pulley.
    • Tighten center bolt to the specified torque.
Torque 167 N-m (123 lb-ft)


  1. Crankshaft pulley; P/S belt
    • Tighten fixing bolt to the specified torque.
Install the belt on the idler pulley.

Mar 07, 2010 | 1993 Isuzu Rodeo

2 Answers

Where is the crank sensor located on a 1999 oldsmobile intrigue 3.5 engine???? easy to replace or not...


usually all crankshaft sensors are located right next to the main drive pulley (Harmonic balancer). As far as being easy is concerned some are not so easy as some require the removal of the harmonic balancer to get to it.. but you might be lucky Gm is pretty good at making the Crankshaft sensor accessible without removing the harmonic balancer.

Dec 01, 2009 | Oldsmobile Intrigue Cars & Trucks

2 Answers

What is the easyist way to check a crank sesor and where is it located on a 2003 taurus


THE BEST WAY TO CHECK CRANKSHAFT SENSOR.IS TO USE A DIAGNOSTIC SCANNER.IT WILL TELL YOU IF CRANKSHAFT SENSOR IS BAD.THE LOCATION FOR CRANKSHAFT SENSOR IS BEHIND CRANKSHAFT PULLEY.

Oct 20, 2009 | 2003 Ford Taurus

2 Answers

To remove crankshaft pulley


no easy way, yopu will need a air impact 1/2" drive. Unles you can get to the flywheel and jam it, or even take the starter out and jam it. with a pry bar or something.

Sep 21, 2009 | Hyundai Motor 2004 Sonata

1 Answer

Need to know what fires coil 1995 mercury sable both wires to coil have power when key is turned on car cranks no spark from coil new coil what gives the coil extra power to fire


what engine? 3.0L 2 Valve? 4 Valve?
3.4L SHO engine?

The PCM (engine computer) fires the coils, but it is never the cause of a problem. I suspect it is the crankshaft position sensor on the front of the engine by the crank pulley. easy to change.

Crankshaft Position Sensor The crankshaft position sensor (CKP sensor) (6C315) is a variable reluctance sensor triggered by a 36-minus-1 tooth trigger wheel located on the crankshaft pulley and damper. The signal generated from the crankshaft position sensor is called the crankshaft position (CKP) signal, which provides base timing and crankshaft speed (rpm) information to the ignition control module (ICM) (12K072). Base timing is set at 10±2 degrees before top dead center (BTDC) AND IS NOT ADJUSTABLE. The powertrain control module (PCM) (12A650) will use this information with the spark advance information to determine ignition coil (12029) turn on or turn off time.

Sep 15, 2009 | 1995 Mercury Sable

1 Answer

Front engine seal leak


clear all pieces you have to get to the crankshaft pulley off. (the big pulley ) you may need to rent crankshaft pulley puller tools (at autozone or advanceautoparts) and get you money back when you are done. its easy be pacient.

Feb 20, 2009 | 2006 Toyota RAV4

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...