Question about 1997 Ford Explorer AWD

1 Answer

My eec relay on my 1992 ford exporler keeps blowing its a 30amm relay the car run for ten to twenty seconds then the relay blow car then the car cranks over but does not start any help would be apprecited.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

There is a short some where in the circuit. Get a Haynes manual part # 36024 covers 91 thru 2000 it will tell you a lot of info on troubleshooting the wiring. Good luck

Posted on Aug 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the ignition switch/plate on 1992 ford explorer


The ignition switch is located in the steering column at the base of the lock cylinder.

Mar 25, 2016 | 1992 Ford Explorer

1 Answer

Should there be fusible links before and after the wire that runs direct from solenoid to the EEC relay?


There can be all sorts of reasons for this...sound more like you have a dead short somewhere. Go here ...
http://www.ford-trucks.com/forums/forum28/ It's free to join, these guys will get you figured out in no time at all.

May 27, 2015 | 1987 Ford Ranger

1 Answer

Where is the EEC relay in a 1992 F-250 with a 7.5 liter


I suggest to check underhood engine bay, according with this wiring diagram, look under EEC (Electronic Engine Control 1992) or PCM (Powertrain Contro Module 1996-1996)...

7_6_2012_11_20_57_pm.jpg

Fig. 22: Engine wiring - 1992-95 F-Series 7.5L (VIN G), 1996 F-Series 7.5L Federal (VIN G) and 1996 F-Series Pick-up 5.8L (VIN H over 8500 GVW) engines - ZOOM LINK DIAGRAM HERE (top left)


ALso, I suggest to check wiring circuit C185, located in THIS LINK DIAGRAM (top right)

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 06, 2012 | Ford Cars & Trucks

1 Answer

EEC relay fuse keeps blowing id put a new fuse in the truck it would run for about 10 seconds then blow the fuse again.


There are 3 relays mounted below the fuse box .
The green I believe is fuel pump relay and the brown is EEC. The third relay is for the A/C WOT.
It is possible the wiring is shorted, check there, it is also possible you have a bad fuel pump.
Please let me know what you find.

Feb 07, 2010 | 1991 Ford Explorer

1 Answer

Ford explorer eec relay


Try a new relay first. This may not be good news if that does not work. If you can find the EEC (computer) and unplug it, then replace the fuse-if it blows you have another cheaper part on the circuit thats bad.
If the fuse does not blow, then the EEC must be shorted.
If you have to replace the EEC you may find a kindly dealer with a cash-for-clunker sitting there to violate. Salvage yards have them, Ebay sells them. I have seen them at swap meets for $20. They are a high price part even rebuilt at Dealers or autoparts stores.

Aug 24, 2009 | 1991 Ford Explorer

1 Answer

1991 ford ranger 3.0 eec relay fuse keeps blowing fuel good no spark.Changed the distribitor, changed the ignition module.


I understand that there is a relay box under the hood with 3 relays. Which is which I don't know. However if you are blowing the fuse TO the ecc relay, then the relay must be bad. This relay controls the spark.

Jul 25, 2009 | Ford Focus Cars & Trucks

1 Answer

EEC fuse keeps blowing


replace with a fuse 5 amps higher than required, keep increasing until it stops

Jun 16, 2009 | 1992 Ford Explorer

1 Answer

EEC fuse: 1992 ford explorer


sounds like you have a bad relay that is shorted out or you might have a bad fuel injector shorting out fossible fuel pump wireing short do some probing aroun with the multi meter try to find direct short , use the process of elimination .
now let me see does your truck start up and run then fuse blows? is the fuse the correct amperage check your owners manual to see how long does it run before blowing fuse ? when its running is it running smooth while is running?

Jul 03, 2008 | 1992 Ford Explorer

2 Answers

E.E.C fuse keeps blowing in 1991 Ford Explorer


sounds like you got a short try tracing harness to see if theres anything visible

May 26, 2008 | 1991 Ford Explorer

Not finding what you are looking for?
1997 Ford Explorer AWD Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...