Question about 1998 Mazda Pickup

1 Answer

I need to how to replace the drivers side mirror on my 1998 mazda b-series 2500 pickup truck. I have the part and like to know if I need to remove the door panel to change the mirror out or if I can just do it from the outside of the truck?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You do need to remove the door panel. There are numerous clips that pop out, two screws, and the screw beneath the roll down lever which can be reached by popping the knob off.

Posted on Apr 06, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My truck started making a bump noise driving home from work today and I could feel it underneath in the middle of the truck. It did it every one-two minutes. It has never done it before. What is it?

look under truck and see if anything is wrapped around drive shaft also if looks good u joints may be going bad also check the center bearing and bracket its a support hanger bearing for driveshaft

May 23, 2016 | 2000 Mazda B-Series

1 Answer

How to find out the plug wire placement on the coil on a 1998 mazda 2500 truck 2wd Has two coils one in front of the other on pass side pls help

Here is a firing order diagram for that vehicle and engine and let me know if you need any help to understand this diagram or if you require any further assistance.


Nov 05, 2010 | 1998 Mazda B-Series

1 Answer

I need a Mazda B Series Fuse box Diagram as I have no manual

need the wiring diagram to replace an aftermarket am/fm radio in 1998 mazda b2500

Aug 05, 2010 | 1998 Mazda Pickup

1 Answer

How do I replace the drivers side mirror on my 1998 chevy s10?

You would have to remove the door panel and then just unbolt the mirror from the inside.

Mar 20, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How do I remove the driver side mirror from a 2003 S-10?

you have to remove the door panel,and then there are 3 nuts to take of and a wire to unplug to get the mirror off.

Feb 19, 2010 | 1998 Chevrolet S-10 Pickup

3 Answers

I have a 2000 Mazda Pickup B3000. need to replace the flasher, where is it located on the truck?

I'm not 100% sure. If there isn't a flasher listed in the fuse panel information or a round (or possibly square) unit in your fuse block that is listed as a flasher in your owner's manual then it may be part of your GEM module.

Oct 03, 2009 | 1998 Mazda Pickup

1 Answer

Mazda b series 4x4 pickup steering keep pulling to one side

Hi I am vortash sounds like you have a problem with either binding brakes on the one side or a suspension fault . this would include wheel bearings , ball joints , track rod ends and , anti roll bar rubbers .. regards Vortash

Jul 13, 2009 | 1998 Mazda B-Series

1 Answer

Need instructions on how to remove passenger side mirror on 1998 dodge ram 2500. they are manual mirrors with no heat or power adjustments.

You should just have to take the cover that looks like a triangle off from the inside of the door. The mirror is then held on by 3 10mm nuts. Remove the nuts, remove the mirror, install in reverse order.

Jun 12, 2009 | 1998 Dodge Ram

1 Answer

I need to replace the passenger sid mirror on a 98

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Apr 22, 2009 | 1998 Mazda 626

1 Answer

B2200 Chassis prt number

They are two totally different frames. The 2200 is a Mazda sourced vehicle while the 2500 is Ford sourced, based on the Ranger pickup.

Mar 11, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
1998 Mazda Pickup Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides