Question about 1986 Nissan Pickup 4WD 1986

1 Answer

1986 nissan pickup z24i. will run when spray start fluid but wont stay running. just installed the engine

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

Did you hook all the lines for the fuel pump up when the engine was re-installed? It is definitely a fuel issue. Disconnect the fuel line and crank over the engine to check for fuel supply.

Posted on Mar 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck starts but will not stay running


Try doing this service.

Engine stalling and rough run issue at low speeds

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control



Jun 23, 2012 | 1995 Nissan Pickup

1 Answer

1986 Toyota p'up starts, but won't stay running once i left off gas pedal


first i would look for a vacuum leaks get it as close to idle as you can when cold and spray carb cleaner around and also check to see if the egr valve is stuck open this will act as a vacuum leak but not detect as one spraying carb cleaner around carb cleaner with change the engine speed near a vacuum leak

Apr 18, 2012 | 1986 Toyota Pickup 4WD

1 Answer

I HAVE A 1986 NISSAN 720 2WD PICKUP. IT HAS A CARB ON IT , BUT DID IT COME WITH A CARB OR FUEL INJECTION?


Its BOTH, sort of....TBI Throttle Body Injection. If you look into the carb with engine running, you will see the injector spraying fuel onto the butterfly.

Aug 23, 2011 | 1986 Nissan Pickup 4WD 1986

1 Answer

1986 nissan d21 4wd with z24 motor it is not getting any fire.the distirb.is working the injector


i am not sure if it has eight plugs or not but if it has two coils , check coils if they seem okay check the modulators thats hookrd to the back of the coil (coils). I have a 1986 nissan hardbody 4x4 w/z24i engine. Check back with me i might be a little help due to i have had resent problems under the hood of mine and maybe have a part or two you can get.

Apr 07, 2011 | 1986 Nissan Pickup 4WD 1986

2 Answers

I have an 87 d21 pickup with a z24i engine. On acceleration on half throttle the engine acts like it is bouncing of off rev limiter. Have changed throttle body, fuel filter, plugs, wires, cap, rotor...


This truck has 2 ignition shstems,One of the modules is malfunctioning. follow the primary wiring from distributor to the ignition modules closeby. Disconnect one at a time untill problem found.

Jan 27, 2011 | 1987 Nissan Pickup

1 Answer

Tears timing chain ajuster off nissan1989 four times


I'm assuming that you are talking about 1989 Nissan Truck 4WD 3.0L FI 6cyl.

In this models, the Z24i and KA24E engines do not use the pin counting method for finding correct valve timing. Instead, set the timing chain by aligning its mating marks with those of the crankshaft sprocket and camshaft sprocket. The camshaft sprocket should be installed by fitting the knock pin of the camshaft into its No. 2 hole. On the Z24i engine, the No. 2 timing mark must also be used.

Excatly, what is the problem? Adjuts timing procedure?

Sep 16, 2010 | 1986 Nissan Pickup 4WD 1986

1 Answer

Need engine size in Nissan pickup


It is either a Z24i, or a KA24E. You should find the identification number on the left side of the block at the rear. It should say what size it is.

Jun 29, 2010 | 1991 Nissan Pickup

1 Answer

A 1986 toyota p.u. 22r how do vacuum lines hook up on engine


Two things to check, do you have fuel, and is the timing good?

Nov 05, 2009 | 1986 Toyota Pickup 4WD

1 Answer

I need the firing order for a 1986 z24i engine and excactly where is the number 1i on the distribuor cap


1 - 2 -3 - 4 - 5 - 6 counter clockwise starting from the #1 plug it will be maked #1 and the #1 plug is passenger side front the firing order is also stamped on the intake manifold.

Jun 19, 2009 | 1986 Nissan Pickup 4WD 1986

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...