Question about 2003 Dodge Caravan

1 Answer

My abs light stays on on the dashboard is there a problem with my brakes or my sensor needs to be replace i had a hub put on one side should i have done both sides

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

If you had a hub replaced, the connector for the ABS system may have just not been plugged back in. Check for an unconnected connector just behind the wheel on the side you had replaced.

Posted on Mar 25, 2011

Testimonial: "thank you for your great "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ABS light coming on stays on ABS wants to fight against the manual until the manual takes over but the lights stay on could that have anything to do service TPM light


didnt specify vehicle --generic answer--check fuses and relays -service pm is a tire pressure sensor system not your braking system ---for the abs have vehicle scanned for trouble code most auto stores offer this service for free ----check the abs sensor wiring and connections they are the wiring connection that runs behind the wheel they can get damaged by debris or age ---check hub/wheel bearing for wear if hub needs replacement abs is incorporated into hub so if hub failure abs can fail also

Sep 25, 2016 | Cars & Trucks

1 Answer

Anti lock brake light stays on


gm is known for their anti-lock brake problems the most likely problem is a build up under the sensor since u have a 93 the abs sensor is incorporated into the hub cheaper to replace the hub w/sensor than to just replace the sensor the hub is not that hard to replace in the 2wd or 4wd----to clean mount jack up vehicle remove the wheel brake caliper,caliper bracket ,rotor and the abs sensor will be in view check the connection and the condition of sensor into the hub if lot of road grime or rust build up use a brush to clean area around sensor than using an allen key remove sensor careful pull straight up plug hole and clean small mounting plate replace sensor ------to replace hub do same in removing components but than need to unbolt hub from rear on 4wd also need to remove cv drive nut replace hub and done

Dec 07, 2012 | 1993 GMC Suburban

1 Answer

The ABS light on my 2005 Grand Caravan has been on (front wheel speed sensors need replacement). The brake light started coming on intermittently and now stays on, checked the reservoir sensor, and the...


The ABS works according to what the speed sensor tells it. The sensor may be bad or it senses a broken tooth on the tone wheel (the sensor reads these teeth on the tone wheel, found in the hub).
You will still have Brakes, but not the ABS. You can switch the sensors from the good side to the bad to see if it is in fact the sensor itself. Good luck!

Aug 04, 2011 | 2005 Dodge Grand Caravan

2 Answers

What causes the indicator lights on the dashboard to go on for the antilock brake and the brake light on a 1998 Chevrolet Lumina 3.1 ?


Low brake fluid,air in brake system,dirty sensors down at the hub or bad sensor at hub, bad sensor at abs or brake master cylinder

Jan 14, 2011 | Chevrolet Lumina Cars & Trucks

3 Answers

My 2003 mercury mountaineer ABS light is staying on. manually, the brakes work however they shimmy.changed the brake pads,checked the brake fluid and ABS fuse,bud when changing the pads,did now clean the...


I replaced the hub bearing assembly on drivers side twice and the light stayed on and the brakes worked fine. It was the wires (visible just above the tire on the frame) that rubbed against the frame that had shorted out. It was simply repaired and clip-stripped up out of the way. The light has been off every since then.

Dec 30, 2010 | 2003 Mercury Mountaineer

1 Answer

ABS lights dashboard stay on i checked abs harness was ok. what is the other cause of this..


It is most likely a wheel speed sensor. It needs to be put on a computer to determine which one. The sensors are in the wheel hub assy.

Jul 09, 2009 | 2003 Pontiac Montana

1 Answer

Dashboard brake light stays on, 1990 Suburban


Most likely. Usually what happens to mine, is the wires to the sensors get broken from stones hitting them. i splice them back together and they are good for a while. Or the sensors get dirty.

May 01, 2009 | 1998 Chevrolet C1500

1 Answer

2005 impala


All the hubs on the car have the abs sensor built into the hub. The abs system has to be re set to read the sensor . The rear hub bearing if noisy should be replaced. There are wiring harnesses that connect to the abs sensor. The harnesses to each of the abs sensor should be replaced.

Mar 18, 2009 | 2005 Chevrolet Impala

2 Answers

Abs brake problem


I found my solution on the web a few years ago. My 2002 RVS had permanent ABS lights and no ABS.

It was suggested to check the ABS electrical connections at the brake disks . There are quick connects there and I found a corroded connector on the front passenger side. My wife started the RVS and put it in gear. With the brake pedal pressed, I wiggled the connectors and the ABS light went "off and on" right away. I replaced the connector and it never happened again. It is likely 4 years ago.

Worth a try.

Dec 28, 2008 | 2002 Buick Rendezvous

2 Answers

Abs light emergency light stay on


Hi, You should check for a sligt break fluid leak from the break light switch (attacked to the master cylinder). Yeah, I know this seems strange, but on my 2001 this leak caused all types of problems with lots of dashboard indicators. The leaking switch was a recall for Ford Trucks, but not the minivans. Hope this helps

Oct 08, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...