Question about Chevrolet 1500

1 Answer

I have a 1998 chevy pickup chennye 4.3L and i can't find where my oil presure switch goes ...i need to change it and can't find it please help me thank you carroll bailey

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

Oil pressure switch is next to distributor

Posted on Mar 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Breack d'ont works bulls all are ok fus ok !! i check inside of swictcht ok on my chevrolet s10 v6 4,3l auto 1997 thks GEORGES jobymib501@hotmail.com or do you have the shema of the wiring or the...


I fixya thanks for reply i just check on the switch inside they no contact betewen the lamell !!! everyting was ok fus bulls cabls just the probleme was inside the switch  is ezy to open by your self  L G

Jan 30, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

Car starts and cuts out after 2 to 3 seconds. fuel


When the ignition switch is turned on the pcm turns on the fuel pump by energizing the fuel pump relay. The PCM keeps the fuel pump on as long as the engine is cranking over or running.It does this by recieving pulses from the ignition module. If there are no referance pulses the PCM will turn the fuel pump relay off in 2 seconds with the ingnition on.

Most models also include a secondary control path through the oil presure switch witch will turn the fuel pump on after it detects oil presure.cranking time will be longer if the fuel pump doesn't recieve current until oil presure switch contact is closed.

Jan 28, 2010 | 1998 Chevrolet K2500

1 Answer

Oil pressure gauge goes up when car started, but then down to 0


u Have a problem with the oil sending unit. The sensor is located beack right side of the engine block. Take out the switch and make sure u have good oil PSI. Should be 6 psi at idle and around 50 at 4000 RPM. If the presure is ok replace the switch they are very cheap about 20 bucks. Please rate.

Aug 10, 2009 | 1998 Jeep Wrangler

1 Answer

98 chevy s-10 2wd is it possible to change the oil pan gasket without pulling the motor? can i just pull the mount bolts and jack it up?


Yes it is possible but you will have to get about six inches of clearance so the pan will clear the oil pump pickup

Jun 22, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Oil sending unit


Hi,

It's usually threaded into the bottom of the block near the oil filter, it should have a wire running from the top of it.

Thanks.

May 29, 2009 | 1998 Chevrolet S-10 Pickup

5 Answers

Where is the oil sending unit located on a Chevy S10 Pickup.


MY S-10 IS LEAKING OIL. I WANT TO KNOW WHERE THE OIL SENDING UNIT IS.

May 29, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

2 problembs 1 oil presure goes down on acceleration but no eng noise.2code for turbine input speed sensor circuit a what is this


I can help with problem 1, maybe. Check your oil and oil filter first. If those are okay, then you may need to drop the oil pan and see if the oil pickup has become clogged with debris, if it has, clean it off and put it back together. If that fails, you may need a new oil pump.

May 25, 2009 | 1995 Oldsmobile Aurora

1 Answer

Wiring Diagram 1998 Chevy S-10 starter replacement


The starter has one large cable from the battery positive, and a wire that goes to the solenoid (Part of the starter) that becomes hot when the key ignition is turned to start. This also passes through the neutral safety switch. (So it wont start in gear) Not sure if this is what you need, a little vague.

May 10, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Where is the oil pressure switch located on the 1998 Chevy tracker


Hello jcreech11: The oil pressure switch is located on side of block just above the oil filter.Should you need further help just ask.Please rate the information as that also helps. Thank You for using FixYa. Roger

Apr 16, 2009 | 1998 Chevrolet Tracker

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...