Question about Ford Edge

Open Question

What color are the IAT sensor wires for a 2007 Ford Edge 3.5L

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 375 Answers

SOURCE: 2007 gmc sierra 2500 IAT sensor

Well, the IAT (Intake Air Temperature) sensor is located on the air intake duct between the filter and the throttle body (Assuming you have the 6L motor). The wires are easily visible at the plug that connects the sensor to the wiring harness. That's the easiest place to access them.

Posted on May 18, 2008

SOURCE: where are the IAT sensor

Check out www.trailvoy.com.

Posted on Sep 04, 2008

fastboyz
  • 674 Answers

SOURCE: 2008 E-350 IAT sensor wires

is this what you recieved?9af2263.jpg

Posted on Nov 12, 2008

Molson02536
  • 3854 Answers

SOURCE: installing chip and want to double check wiring. Need to find IAT/MAF sensor diagram for 2003 Ford Ranger

Save your money, the chip is a ohm resistor at Radio Shack for under $2.00. It splices in to you IAT wire harness located at the intake tube between the air filter housing and throttle body.
Problem with this system is, that you can not adjust anything and have to run a constant 91 octane just to make sure you do not have a Detonation. The ECM will catch the Detonation from the knock sensor and compensate for it by retarding the timing which in turn lose of HP till next start up.
If you like and don't mind the check engine light on once and awhile, you can do the same by just disconnecting the IAT wire harness which give the ECM a 0 resistance thinking it's -20 out side and turn the timing up and lengths the injector pules.
When i was running a Nitro in the Toy before i sold it, i had installed a 10K ohm Potentiometer which you can buy at radio shack for under $5.00 i believe, I just spliced it in to the IAC wire harness so if i wanted to play with the Nitro I'ld turn the resistor up making the engine think it's 185 degrees F and would ****** the timing so i would not hurt the engine. But if i wanted to get more timing i would just turn the knob to drop the resistance to get more time since the engine thinks it's -20 out side.
Hope this helps. Keep me posted if you need more info. Best thing is to do a dyno tune and you can change everything right down to the Shift points.

Posted on May 29, 2009

  • 18 Answers

SOURCE: wire colors for my IAT sensor

red with blue stripe and black... cut the red with blue strip and connect one end of the resistor to the harness side. Then splice the other end of the resistor to the black wire... do not cut it just splice into it.

Posted on Dec 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What colors are the wires for the iat sensor for a ford e350 5.4 liter?


I did a quick Google search for "iat wires for e350", looked at the image(s) results - lots of images with digragms, color codes etc.
Try it yourself RE: you may recognize your configuration.. and find the diagram for your vehicle.

Jan 10, 2015 | Ford Cars & Trucks

1 Answer

What 2 wires for iat sensor


you lost the colors.? or are there 2 wires there that you know are IAT but dont know which pin fit them.?
no matter, either pin works.
the sensor is not electronic, its just a resistor, that is non polarized
the ECU sends current to the IAT, the current that flows, tells the
ECU what the air temperature is. in the intake.
no car year stated
no engine option stated in F150
so NO ANSWER exact , ever. (country helps too, but ill not say that it scares folks to death for some reasons)
Im in USA and ford does EXPORT cars and trucks.
the IAT is a thermistor, the FSm shows how it works and how
to test one easy, super easy, ask.

tell more get more.

Jun 14, 2014 | Ford F-150 Cars & Trucks

1 Answer

2007 BMW 328i IAT Wire Colors in MAF Sensor


If you are installing a so called "chip" don't do it, it can harm the engine due the changes it causes in fuel control as related to Intake Air Temperature and burn holes in the pistons. All that little part really is, is a $.50 (50 cent) resistor that you can buy from Radio Shack, it is smoke and mirrors and it also will void any warranty you may have. I for one strongly advise against installing it, it will make not difference in power and all there claims are just lies and falsehoods..

Jun 08, 2012 | BMW Cars & Trucks

1 Answer

Need the color of the two wires going from the plug to the iat/maf sensor on a 2006 ford taurus


The first and sixth wire are IAT.------

That is grey wire and grey with red wire.-------

The first one is only grey and second one is gery/red wire.

---------

This will help.Thanks.Helpmech.

Sep 07, 2011 | 2006 Ford Taurus

1 Answer

What color wires lead to the IAT sensor on a 2005 ford f250 6.0 powerstroke?


Hello! The Intake Air Temperature (IAT) sensor has the following wire colors...Gray/Red and Gray...


Guru...Saailer

Jan 04, 2011 | 2005 Ford F 250 Super Duty

1 Answer

My maf sensor pigtail was cut and stolen. I purchased a new pigtail from ford and I need to know the color codes so I can intall a new one. my vehicle is a 2004 ford f-150 lariat with a 5.4 liter engine....


As long as you are talking about the new body style ( 3V 5.4 L )

The module is the MAFS and the IAT sensors

The IAT section is :
PCM to IAT is Gray wire
The return to the electronic engine controls from the IAt is Gray w/ REd stripe wire

The MAFS
PCM to MAFS ( MAF ) is Light Blue w/ Red stripe wire
The MAF return on the PCM is Tan w/ Light Blue stripe wire
The ground ( same as the Charge motion control valve ) is Black w/ White stripe wire.

Apr 01, 2010 | 2004 Ford F150

1 Answer

What color are the wires for the iat sensor on a 2009 f-150 w/ 5.4 l


the iat is part of the maf sensor located in the air filter duct or housing. 6 pin connector. pin one color violet/gray is for iat. pin 2 is c-signal rtn yellow/violet. pin 3 maf yellow/violet. pin 4 maf rtn blue. pin 5 ground black/yellow pin 6 circuit breaker fuse 76 blue/brown

Mar 05, 2009 | 2009 Ford F-150

1 Answer

IAT Wire Colors


the IAT should only be a 3 wire plug not 6

Jan 20, 2009 | 2007 GMC Yukon

1 Answer

IAT sensor


the iat 5 volt referance is tan/black in pin d- the sensor return is tan on e-maf sensor ignition power is pink in b cavity- c is ground and black/white -a is the maf signal and yellow

Nov 12, 2008 | Daewoo Lanos Cars & Trucks

1 Answer

2008 E-350 IAT sensor wires


is this what you recieved?9af2263.jpg

Nov 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...