Question about 2008 GMC Acadia

Open Question

How many grease fittings are there on a 2010 GMC Aadia?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to I change the headlight on my 2010 GMC Acadia?


Search "headlamp replacement 2010 GMC Acadia* & got a number of hits. Suggest you try and select best fits.

Jun 16, 2015 | 2010 GMC Acadia

1 Answer

How to chassis lube a 2010 chevy malibu


You are not taking a boot off the grease fitting. The little rubber boot you're removing is the dust boot for the bleeder valve on the brake caliper. The 2010 Chevy Malibu,as with most cars, have non-serviceable suspension parts.

Feb 23, 2015 | Cars & Trucks

1 Answer

How do i make sure i have greased all of my grease fittings


You should have one fitting on each upper and lower ball joint, (4 total), and you may or may not have fittings on each of the four tie rod ends. Don't overgrease any of them, they only need one or two strokes of the gun. I think that is all you have. Some cars have a fitting on each end of the upper A-arm, but GM generally uses a rubber bushing there instead, no grease required. The lower suspension arm to the frame is almost always a bushing and needs no grease.

You *might* have fittings on your driveshaft universal joints, although these need a special "needle" fitting to reach them. Most u-joints don't have fittings, however. If you have them, they are standard fittings located in one of the four inner "corners" of the joint, near the center.

Oct 10, 2010 | 1997 GMC Sierra

1 Answer

Is there any greasing nipples for the GMC envoy slt 2003 ? & If any where are located? squeaking noise at the left front


There are no grease fittings on most of today's cars. The squeaking noise may be coming from a dried out suspension bushing.

Sep 13, 2010 | 2003 GMC Envoy

1 Answer

My 2004 gmc sierra has a slight squealing noise when turning left


If noise is come from front end, and your truck is not moving at a stand still, it's going to be your ball joint's, bad news, if there OE there will be no grease fitting. New ones will come with grease fitting for future lube jobs on ball joint's.

Jul 19, 2010 | 2002 GMC Sierra 1500

2 Answers

Is there any grease fittings on the front and rear


There should be some on the front end steering linkage, and some on the drive shaft front and rear, there is none on the rear end.

Jun 10, 2010 | 1993 GMC Jimmy

3 Answers

AFTER GREASING BOTH UPPER BALL JOINTS ON 2006 GMC 2500--GREASE SPITS BACK OUT--INITIAL LOOKED TO BE OLD GREASE, I AFTER A COUPLE DAYS WENT TO REGREASE AND NOW THE NEW GREASE SHOOTS BACK OUT.


you don't want to over grease 2or 3 pumps should be good at every oil change but if it isn't taking grease in the zerk a Little tap on top may fix it or you should unscrew it and replace with new

Mar 12, 2010 | 2006 GMC Sierra

2 Answers

Flasher relay is clicking when signals are not in use?


Those are the typical symptoms of a problem with the mutifunction switch. The dielectric grease becomes impregnated with metal flakes, which jumps the contacts inside the switch. The clicking that you hear is the flasher relay located behind the glove compartment. Replacing the switch is not that hard for a DIYer. Some guys have remedied the problem by taking the switch apart, cleaning out the old grease, and applying new grease.
File In Section: Product Recalls
Bulletin No.: 01073A
Date: July, 2002
PRODUCT SAFETY RECALL
SUBJECT:
01073A - STOP LAMPS/HAZARD LAMPS INOPERATIVE
MODELS:
2000-2001 CHEVROLET BLAZER AND TRAILBLAZER (CLASSIC); GMC JIMMY AND ENVOY (CLASSIC); AND OLDSMOBILE BRAVADA (CLASSIC)
2002 CHEVROLET BLAZER; GMC JIMMY AND ENVOY (CLASSIC)
This bulletin cancels and replaces bulletin 01073, issued April, 2002. All copies of bulletin 01073 should be destroyed.
Due to parts availability, this recall was administered in two phases. This is the second and final phase of the recall. The Parts section has been revised to include parts for this second phase.

Jan 29, 2010 | 2000 GMC Jimmy

2 Answers

Do I need to add a grease fitting for the Steering Rods?


those other components are sealed and supposedly do not require added grease. You are able to go to a part store though and purchase a grease needle to inject into the boot if you feel it needs it.

Sep 03, 2009 | 2004 GMC Savana

1 Answer

I'd like to grease the front and rear axles but can't locate the grease nipples.


Check the area where the fittings should be.The holes may be plugged, you will have to remove the plugs and install grease fittings.
Hope this is of some assistance.
Ed.

Apr 18, 2009 | GMC Yukon Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...